Bedienungsanleitung Audiosonic SCZT2 (Seite 28 von 32) (Englisch)

618699

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

VQT2R71

Troubleshooting guide

Troubleshooting and

other information

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, consult your

dealer for instructions.

Troubleshooting guide

Problem Possible solution Pages

No power. • Ensure the AC mains lead connected. 14

“2CH SEARCH ” or “4CH

SEARCH ” does not go off

on the display while setting

the speakers.

• Make sure that the speakers are on.

 If the display does not go off even when the speakers are on, consult your

dealer.

15, 17

No sound or image after

playback starts.

• Select the correct source.

• Turn the muting off.

• Check that the digital signals can be decoded by this system.

With the optical fibre connection, cannot playback PCM signal with sampling

frequency of over 96 kHz.

• Check connections to other equipment.

• (When the audio is not heard from TV) The optical fibre cable or stereo phono

cable is necessary to connect with a TV incompatible with ARC. For details,

refer to the operating instructions for the connected TV.

• Set “AUTO ” in “Switching the input signal detection setting”.

• Turn this system off then on again.

• Make sure that the speakers are on.

• Make sure that the speakers have been properly set.

• Adjust the speakers.

• If the connections are normal, this may be a cable-related problem. Use other

cables and make connections again.

10 to 13

—

15, 17

22, 23

—

The remote control does

not work.

• Replace the batteries if they are worn.

• Make sure the remote control code has been properly set.

No sound from microphone

connected to DVD player (karaoke)

•

No sound is output from microphone if this system is digitally connected with DVD player.

Change to analogue connection and input. Make analogue connection to AUX3 IN.

12, 13

There is no DTS audio output.

There is audio output, but the

DTS decoder indicator is not lit.

• Set the DTS Digital Audio Output setting on the DVD player, Blu-ray Disc

player or DVD recorder to Bitstream.

• Set “DTS ” in “Switching the input signal detection setting”.

—

Sound is not heard when

playing DVD audio.

• This may occur due to digital copyright protection of the disc if using optical

digital connection. This system may not be able to play sources with sampling

frequency of over 48 kHz.

—

“F70



” appears on

the display.

(“DSP ” or “HDMI ” is

displayed in



• Turn off the system, unplug the AC mains lead, and consult your dealer. —

“F76 ” appears on the display.

(After displayed, the system

turns off.)

• Unplug the AC mains lead, and consult your dealer. —

No sound in surround

mode.

• Set to Dolby Virtual Speaker, Dolby Pro Logic or SFC.

• (When the audio is not heard from TV) Check if this system is connected to TV

with the optical fibre cable or the stereo phono cable properly.

10 to 12

Cannot use Dolby Virtual

Speaker, Dolby Pro Logic

or SFC.

• You cannot use these features with PCM signals with sampling frequency of

over 48 kHz. Make analogue connection to AUX3 IN.

• You cannot use for Dolby Digital dual sounds.

12, 13

—

When using an HDMI

connection, the ﬁ rst few

seconds of sound is cut off.

• This may occur if you start play from a chapter on a DVD. The following will

correct the problem.

1 Change the audio output setting on the Blu-ray Disc player, DVD recorder or

DVD player from Bitstream to PCM .

Change input signal setting to “PCM ” in “Switching the input signal detection setting”.

—

The system does not work

properly.

•

The system does not work properly if you have connected the HDMI input and output terminals

incorrectly. Turn the system off, unplug the AC mains lead, and make the connection again.

Could watch TV (VIERA)

when installed, but now

cannot watch TV.

• When using this system in combination with TV (VIERA) only, check if HDMI

cable is not connected to “BD/DVD IN” or “AUX1 IN” of this system. If it is

connected to “BD/DVD IN” or “AUX1 IN”, connect to “TO TV (ARC)”.

—

The sounds of the ﬁ rst few

seconds are cut off when

playing back 7.1-channel

LPCM signals.

• This may occur when playing back 7.1-channel LPCM signals of a Blu-ray

disc. Press [

SKIP] on the remote control of recorder or player to play back

again from the beginning.

—

HDMI Sound ﬁ eld

Common problems

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiosonic SCZT2 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Audiosonic SCZT2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info