Bedienungsanleitung Audiovox AA-RS30CS (Seite 2 von 20) (Englisch)

583736

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The AA-RS30CS is Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles

Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may

be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug

pre-heat system), feature #9 should remain in the default Gasoline mode setting. For diesel applications, consult your

dealer for the type of ignition system used in your particular vehicle. Regardless of the vehicle, Gasoline or Diesel, for

every installation, the vehicle MUST HAVE a Tach Signal Input, and an Automatic Transmission.

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location

selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness.

Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the module

to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or block the

steering wheel preventing proper control of the vehicle. Secure the module in the chosen location using cable ties or

screws as necessary.

Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

HOOD PIN SWITCH:

The pin switch included in this package is required for the safety shut down of the remote start unit. If the vehicle is

being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This

switch MUST be installed in all applications Failure to do so may result in personal injury or property damage. Mount

the switch in an area under the hood that is away from water drain paths. If necessary, the included brackets may be

used to move the switch away from rain gutters or allow mounting to the firewall behind the hood seal. In either case

the switch must be set up to allow the hood door to depress the switch at least 1/4 inch when the hood is closed and fully

extended when the hood is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind the

chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired

location and thread the pin switch into it using a 7/16" nut driver or deep well socket. If using the mounting bracket, first

secure the bracket to the desired location and secure the pin switch in the pre-threaded mounting bracket hole.

THE RECEIVER/ANTENNA ASSEMBLY:

The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board

for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.

Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window

glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window location for

best reception. Secure the antenna with double stick tape provided. After securing the antenna, we advise also

securing a section of the antenna cable to a fixed support. This will prevent the antenna from dropping down in case

the double stick tape is exposed to extreme heat which may loosen it's gummed surface.

PROGRAM SWITCH :

Select a mounting location that is within reach of the ignition switch, as this switch, in combination with the ignition

switch, will be used to program the selectable features of the system. It is suggested that the switch be mounted to the

lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is allowed

for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4"

hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the

switch using the nut, star washer, and on/off face plate. It is best to orientate the switch to allow the on position to be

up toward the driver and the off position to be down or away from the driver. Route the switch wires toward the control

module.

CONTROL SWITCH:

Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick panel, or

glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is allowed for the body

of the switch and also that the drill will not penetrate any existing factory wiring or fluid lines.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox AA-RS30CS Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info