Bedienungsanleitung Audiovox AA-RS30CS (Seite 3 von 20) (Englisch)

583736

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside.

Secure the switch using the nut, star washer, and on/off face plate. It is suggested that the switch be oriented to allow

the on position to be up toward the driver and the off position to be down or away from the driver. Route the switch

wires toward the control module. Place the RED rubber boot, included in the kit, over the switch handle to differentiate

this switch from the program switch.

The AA-RS30CS is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination

Keyless Entry/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed

into a vehicle with a manually operated transmission. Doing so may result in serious personal injury and property

damage.

IMPORTANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT

HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE

BEEN MADE. AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT

THE NEGATIVE BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY

CONNECTIONS.

WIRING THE 6 PIN MAIN POWER HARNESS:

RED w/WHITE Trace Wire: + 12 volt Battery 1 Source

Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and

holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.

RED Wire: + 12 Volt Battery 2 Source

Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and

holder provided, but NOT the same vehicle wire as used by the battery 1 source. Most vehicles have more than one

battery source supplying power to the ignition switch. Separate feed wires must be used for the Red and Red/White

wires. If your vehicle does not have two battery feed wires at the ignition switch then it is possible to connect both

wires to the vehicle's battery. This wire provides power for the start relay and the accessory relay.

IMPORTANT! It is the responsibility of the installing technician to determine the load factor of the vehicles electrical

circuits when the vehicle is running and to adequately fuse the two power wires based on that load. If

the vehicle, running under load with the air conditioner, heater blower motor, and accessories

exceeds 24 Amps continuous, we recommend that two fuses be used in combination on each power

wire as shown below. For additional information see Tech Update issued 9/30/96.

YELLOW Wire: Starter Output

Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while

in gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow

you to properly identify the circuit and select the correct installation method. In addition you will realize why

the connection of the safety wire is required for all mechanical switch configurations.

Failure to make this connection properly can result in personal injury and property damage.

In all installations it is the responsibility of the installing technician to test the remote start unit and assure that the

vehicle cannot start via RF control in any gear selection other than park or neutral.

In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wire will be made to

the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts when the ignition switch

is turned to the start (crank) position only. This wire will have 0 volts in all other ignition switch positions.

NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral

switch configuration, this connection must be made between the starter inhibit relay, (when used) and the

neutral safety switch as shown in the following diagram.

Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and

property damage. (See feature # 10 for OVERCRANK information)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox AA-RS30CS Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info