Bedienungsanleitung Audiovox APS-45 (Seite 7 von 8) (Englisch)

583772

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

FEATURE ACTION TO PERFORM RESPONSE FROM SYSTEM LED FLASH PATTERN

To Turn the Ignition Switch ON LED Turns OFF

Enter Toggle the Valet/Program/Manual Override Switch

The ON then OFF 3 Times 1 Siren/Horn Chirp & 1 LED Flash

Programming Within 3 seconds

Mode turn the Ignition Switch OFF, then ON 1 Short Chirp, and 1 Long Chirp

First Press Transmitter Button 1 to Change Feature 1 Chirp = Passive Arming ON 1 Flash, Pause, Repeat

2 Chirps = Active Arming ON

Second Press Transmitter Button 1 to Change Feature 1 Chirp = Ign Locking ON 2 Flashes, Pause, Repeat

2 Chirps = Ign Locking OFF

Third Press Transmitter Button 1 to Change Feature 1 Chirp = Ign Unlocking ON 3 Flashes, Pause, Repeat

2 Chirps = Ign Unlocking OFF

Fourth Press Transmitter Button 1 to Change Feature 1 Chirp = Chirps ON 4 Flashes, Pause, Repeat

2 Chirps = Chirps OFF

Fifth Press Transmitter Button 1 to Change Feature 1 Chirp = Passive Doorlock ON 5 Flashes, Pause, Repeat

2 Chirps = Passive Doorlock OFF

Sixth Press Transmitter Button 1 to Change Feature 1 Chirp = Steady Output (siren) 6 Flashes, Pause, Repeat

2 Chirps = Pulsed Output (horn)

Seventh Press Transmitter Button 1 to Change Feature 1 Chirp = 800ms Lock Pulse 7 Flashes, Pause, Repeat

2 Chirps = 3.5sec Lock Pulse

3 Chirps = 800ms Lock Pulse

800ms Double Unlock

You have now engaged the Programming Mode, and are set to adjust the First feature

This mode will time out automatically in 15 seconds, or can be cancelled by turning the Ignition Switch OFF

Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature

Turn the Ignition Switch OFF to exit the Programming Mode

NOTE:

If you accidentally toggled past the feature you intended to adjust, you must exit and re-enter the mode.

Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature

COMPLETING THE INSTALLATION:

After you have confirmed the operation of the APS-45, and tested any and all optional features of the system:

1. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain that the

chosen mounting location will not inhibit any of the controls of the vehicle.

2. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact with

under the dash board or in the engine compartment areas.

CAUTION:Particularly avoid the area around the steering shaft and column, as wires can wrap around these

mechanisms and impair the safe operation of the vehicle.

3. Check the vehicle's wipers, lights, horn, etc... to insure proper operation.

4. Replace all panels that were removed during installation, and retest the system.

5. Explain the operation of the system and its various features to the end user if available, and place the Owner's

Manual on the dashboard for them to find and review.

NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between steps, or

the programming mode will be terminated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox APS-45 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info