Bedienungsanleitung Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II (Seite 54 von 122) (Englisch)

815458

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

7 | Requirements at the installation location EN Operating manual Fireplace inserts slied flat + II

Combustion air supply via direct duct (balanced flue operation)

The combustion air supply can also be fed via a direct duct from outside to the fireplace insert. For this

purpose the combustion air must be safely routed from the house’s external air connection directly to

the combustion air trunking.

The duct cross-section can be determined with the help of the pressure-volume diagram (see technical

rules of the Stove- and Air Heating Constructors Association). See Section “Min. cross-section of chim-

ney combustion air duct”. This method of connection is generally recommended.

Combustion air supply from the room (balanced flue operation)

The Austroflamm fireplace insert obtains its combustion air exclusively via the direct combustion air

trunking directly from the installation room.

For all the models described in this manual you will find the combustion air trunking on the underside

of the combustion chamber. For this reason a faultlessly working combustion air feed into the heating

chamber must be ensured. This absolutely requires the correct dimensioning of the circulating air

cross-sections, in addition to the necessary combustion air cross-section. The correct positioning of the

corresponding openings into the heating chamber is very important.

Non-compliance can cause a lack of air during combustion.

Fig.4: Combustion air trunking

The combustion air trunking must always be connected, as

otherwise no combustion air is routed into the firebox.

7.4 Combustion air duct

Combustion air ducts must be made of dimensionally stable construction materials, sealed and access-

ible for inspection and cleaning. Consideration must be given to possible condensation formation

from falling below the dew point and prevented by suitable insulation.

For combustion air ducts in buildings with more than 2 full storeys and combustion air ducts which

bridge firewalls, the ducts must be executed so that fire and smoke cannot be transmitted into other

storeys or fire sections (see state building regulations).

7.5 Chimney requirements

Before set-up or installation of the Austroflamm fireplace insert, the chimney must be checked for its

size and quality under the existing local regulations (respectively state building regulations, heating

regulations and DIN 18160, Part 1). The mathematical proof of the adequate function of the chimney

must be provided in accordance with EN 13384. Consideration must be given when making the calcu-

lation that the substantially greater quantity of air can also be safely removed when the door is open

(stoking up fuel).

The operation of your Austroflamm fireplace insert is primarily dependent upon the faultless working

of the chimney.

TIP

Care must be taken that all openings, such as openings for cleaning, of fireplace being used are

closed during operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info