Bedienungsanleitung Autotek TA2150 (Seite 9 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

701388

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

IMPORTANT NOTES PRIOR TO INSTALLATION

- This device is only suited for a 12 volt system with negative ground.

- Theradiatedheatwhileoperationrequiressufcientaircirculationattheplaceofinstallation.Itis

veryimportantthattheheatsinknsdonothavecontactwithanymetalpartsoranysurfaceswhich

couldimpairaircirculation.Theampliermaynotbeinstalledinsmallclosedlocationorspaces

without air circulation (e.g. spare wheel recess or below the vehicle carpeting). We recommend the

installationinthevehicle’strunk.Ensuresufcientprotectionagainstvibrations,dustanddirt.

- Ensurethattheinputandoutputcablesaresufcientlyseparatedfromthepowersupplycables.

Otherwise interferences may occur.

- Ensure the accessibility of the fuse and the operating elements after installation.

- Thereliabilityandperformanceoftheamplierdependsonthequalityofinstallation.Preferably

consult an expert to install the system, particularly if you want to install several loudspeakers.

POWER SUPPLY AND TURN-ON-CONNECTION

INTERCONNECTION

ATTENTION: Before you start with the installation, disconnect the ground connection from the ve-

hicle’s battery in order to prevent short circuits.

Thepowerwiringwhichisusuallyinstalledinon-boardcarnetworksisnotsufcientforapoweramplier‘s

demands.MakesurethatthepowerwirestoGNDandtothe+12Vterminalhasbeensufcientlyspecied.A

cable cross section of at least 10 mm

mustbeusedtoconnectthebatterytotheamplier‘sterminals.

FirstconnecttheGNDterminaloftheampliertoanappropriategroundconnectionatthechassis.Toensurea

good connection, residue dirt and dust from the connection point. A loose connection may cause malfunctions

or interferences noise and distortion.

Thenconnectthe+12Vterminaloftheamplierwiththebatterybyusinganappropriatecableincludingan

in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30 cm

away. Only insert the fuse when the installation, including the connection of the loudspeakers, has been ac-

complished.

Thenconnect theremoteturn-on-wire from theheadunit withtheamplier‘s REMterminal.A cablewitha

cross-section of 0.5 mm

is adequate.

LOUDSPEAKER CONNECTIONS

- In2-channeloperation(i.e.oneloudspeakeroneachamplierchannel),theimpedancemust

not be lower than 2 ohms for each speaker

- Inbridgingmode(twoamplieroutputscombined)theimpedancemustnotbelowerthan4ohms

for the bridged output.

- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.

Iftheamplierisoperatedwithatoolowimpedanceorincorrectlyused,theentiresoundsystemmaybedam-

aged. This means a warranty void in such cases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Autotek TA2150 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info