Bedienungsanleitung Autotek TA2150 (Seite 10 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

701388

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

AUDIO SIGNAL CABLES

WheninstallingtheaudiocablesbetweentheRCAoutputsoftheheadunitandtheRCAinputsoftheamplier,

the audio and power supply cables should, if possible, not be routed along the same side of the vehicle. We

recommend a separated installation, e.g. routing the power cable through the cable channel on the left side

and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents

interferences due to crosstalk into the audio signal.

INPUT SENSITIVITY

OPERATING ELEMENTS

TurntheGAIN(Fig.1,3)controlleroftheampliertotheMINposition.Thenturnthevolumecontrollerofthe

head unit to 80 - 90% of its full setting. Now turn GAIN clockwise until you hear some distortion. Then turn back

the GAIN slightly until you hear a cleaner sound.

HIGH LEVEL INPUTS

TheHIGHIN(Fig.1,2)issuitabletoconnecttheamplierinputswithspeakerwires,ifyourheadunitisnot

equippedwithpre-amplierRCAoutputs.Extendthereforeveryregardingspeakercablefromyourheadunit

withappropriatespeakercablesfromyourcaraudioretailertothemountinglocationoftheamplier.Thencon-

nect the each matching loudspeaker cable with the cables of the included HIGH IN jack like described below.

ATTENTION: Never use the High Level Input and the RCA inputs at the same time. This may damage the

amplierseriously.TheloudspeakercablesoftheHIGHINmusthavenocontacttotheground(GND)byany

means.

grey = speaker - right - positive

brown = speaker - right - negative

white = speaker - left - negative

green = speaker - left - positive

VARIABLE HIGH PASS FILTER

Iftheamplieristobeusedformid-range/tweeterloudspeakers,settheswitchesX-OVER(Fig.1,6)toHPF.

Then set the desired cross-over frequency on the HPF controller (Fig.1,7). Thus to that only the frequencies

abovethechosencross-overfrequencywillbeamplied.Thiseffectivelyminimizesdistortionsandoverloads

at lower frequencies. A good point to start is at 125 Hz.

If you use loudspeakers (>20 cm) set X-OVER (Fig.1,6). to ”FULL”. In this case, the HPF controller are without

function (Fig.1,7).

VARIABLE LOW PASS FILTER

If theamplier is usedto drive asubwoofer,set theswitch (Fig. 1,6) to „LPF“. Set the desired cross-over

frequency by using the controller (Fig. 1,5). Thus to that only the frequencies below the chosen cross-over

frequencywillbeampliedandthesubwooferplaysmorepreciselyandefcient.

SWITCHABLE BASS EQ

By using the BASS EQ switch (Fig.1,4) you are able to increase the bass level by 6 or 12 dB at 60 Hz.

Attention: Use the BASS EQ wisely!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Autotek TA2150 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info