Bedienungsanleitung Baby Lock Accord BLMCC (Seite 195 von 204) (Englisch)

661179

195

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Troubleshooting

Appendix A-17

MAINTENANCE AND TROUBLESHOOTING

High-pitched

sound while

sewing

Dust or lint is caught in the feed dogs. Remove the dust or lint. A-2

Pieces of thread are caught in the race. Clean the race. A-2

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine.

B-23

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-17

There are needle holes or friction scratches in

the bobbin case.

Replace the bobbin case, or consult your

authorized Baby Lock retailer.

A-2

Fabric does not

feed through the

machine.

Feed dogs are set in the down position. Slide the feed dog position switch to the right

().

B-2

Stitches are too close together. Lengthen the stitch length setting. B-41

Wrong presser foot was used. Use the correct presser foot. B-34

Needle is turned, bent or the point is dull. Replace the needle. B-31

Fabric does not

feed through the

machine.

Thread is entangled. Cut the entangled thread and remove it from the

race.

A-8

Zigzag foot “J” is slanted on a thick seam at the

beginning of stitching.

Use the presser foot locking pin (black button

on the left side) on zigzag foot “J” to keep the

presser foot level while sewing.

S-4

Presser foot pressure is set incorrectly for

fabric.

Adjust presser foot pressure within the settings

screen.

B-45

The fabric feeds in

the opposite

direction.

The feed mechanism is damaged. Contact your authorized Baby Lock retailer. –

The needle

contacts the

needle plate.

The needle clamp screw is loose. Firmly tighten the needle clamp screw. If the

needle is bent or blunt, replace it with a new

one.

B-31

Needle is turned, bent or the point is dull. Replace the needle. B-31

Fabric being sewn

with the machine

cannot be

removed.

Thread is tangled below the needle plate. Lift up the fabric and cut the threads below it,

and clean the race.

A-8

A broken needle

has fallen into the

machine.

- Turn off the machine, and remove the needle

plate. If the needle that fell into the machine can

be seen, use tweezers to remove it. After

removing the needle, return the needle plate to

its original position and insert a new needle.

Before turning on the machine, slowly turn the

handwheel toward you to check that it turns

smoothly and that the new needle enters

through the center of the needle plate opening.

If the handwheel does not turn smoothly or the

needle that fell into the machine cannot be

removed, consult your authorized Baby Lock

retailer.

A-8

The handwheel

feels sluggish

when it is turned.

Thread is tangled in the bobbin case. Remove the tangled thread from the bobbin

case. Re-install the bobbin case so it is

correctly positioned.

A-6, A-8

Symptom Probable Cause Remedy Reference

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Accord BLMCC Seite 195

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Accord BLMCC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info