Bedienungsanleitung Baby Lock Accord BLMCC (Seite 196 von 204) (Englisch)

661179

196

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Troubleshooting

A-18

■ After sewing

Symptom Probable Cause Remedy Reference

Thread tension is

incorrect.

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine.

B-23

Bobbin is set incorrectly. Reset the bobbin. (If needle plate was removed,

reinstall needle plate and tighten screws prior to

installing bobbin case. Check to make sure

needle enter through the center of needle plate

opening.)

B-20, A-2

Using improper needle or thread for the

selected fabric.

Check the “Fabric/Thread/Needle

Combinations” chart.

B-30

Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. B-33

Thread tension is set incorrectly. Adjust the thread tension. B-42

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-20

Needle is turned, bent or the point is dull. Replace the needle. B-31

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-17

Character or

decorative patterns

are misaligned.

Pattern adjustment settings were set incorrectly. Revise the pattern adjustment settings. D-5

Pattern does not

turn out.

Wrong presser foot was used. Attach the correct presser foot. B-34

Did not use a stabilizer material on thin fabrics

or stretch fabrics.

Attach a stabilizer material. D-4

Thread tension is set incorrectly. Adjust the thread tension. B-42

Fabric was pulled, pushed or fed at an angle

while it was being sewn.

Sew while guiding the fabric with your hands so

that the fabric is fed in a straight line.

B-36

The thread is tangled, for example, in the

bobbin case.

Remove the tangle thread. If the thread is

tangled in the bobbin case, clean the race.

A-2

Embroidery pattern

does not sew out

correctly.

Thread is twisted. Use scissors, etc., to cut the twisted thread and

remove it from the bobbin case, etc.

A-8

Thread tension is set incorrectly. Adjust the thread tension. B-42

Fabric was not inserted into the frame correctly

(fabric was loose, etc.).

If the fabric is not taut in the frame, the pattern

may turn out poorly or there may be shrinkage

of the pattern. Set the fabric into the frame

correctly.

B-58

Stabilizing material was not attached. Always use stabilizing material, especially with

stretch fabrics, lightweight fabrics, fabrics with

a coarse weave, or fabrics that often cause

pattern shrinkage. See your authorized Baby

Lock retailer for the proper stabilizer.

B-58

There was an object placed near the machine,

and the carriage or embroidery frame hit the

object during sewing.

If the frame bumps something during sewing,

the pattern will turn out poorly. Do not place

anything in the area where the frame may bump

it during sewing.

B-57

Fabric outside the frame edges interferes with

the sewing arm, so the embroidery unit cannot

move.

Reinsert the fabric in the embroidery frame so

that the excess fabric is away from the sewing

arm, and rotate the pattern 180 degrees.

B-58

Fabric is too heavy, so the embroidery unit

cannot move freely.

Place a large thick book or similar object under

the arm head to lightly lift the heavy side and

keep it level.

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Accord BLMCC Seite 196

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Accord BLMCC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info