Bedienungsanleitung Baby Lock Accord BLMCC (Seite 198 von 204) (Englisch)

661179

198

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

Troubleshooting

A-20

OK to recall and resume previous memory? This message appears if the machine is turned off while embroidering, then

turned on again.

Press to return the machine to the condition (pattern position and

number of stitches) when it was turned off. Follow the procedure described

in “If the thread breaks during sewing” on page E-24 to align the needle

position and embroider the remainder of the pattern.

Pattern extends to the outside of embroidery frame. This message is displayed when the combined character pattern is too large

for the embroidery frame. You can rotate the pattern 90 degrees and

continue combining characters.

Pattern extends to the outside of embroidery frame.

Add no additional characters.

This message is displayed when the character pattern combination is too

large to fit in the embroidery frame. Change the character pattern size or

layout the patterns to fit the embroidery frame. If “Embroidery Frame

Identification View” is set to “ON”, setting to “OFF” or selecting larger frame

may help.

Pattern extends to the outside of embroidery frame.

This function cannot be used at this time.

This message appears when the embroidery character pattern is resized or

switched between written vertically/horizontally so that it is too large for the

embroidery frame.

Preventive maintenance is recommended. This message is displayed when the machine needs to be maintained. (page

A-3)

Raise the buttonhole lever. This message is displayed when the buttonhole lever is down, a stitch other

than a buttonhole is selected, and the “Start/Stop” button, etc. is pressed.

Selected pattern field extends to the outside of the

embroidery frame.

This message appears when the selected embroidery pattern is larger than

the large embroidery frame. Reduce the pattern size, or select a different

pattern.

This message appears when the selected embroidery pattern is larger than

the embroidery frame selected when “Embroidery Frame Identification View”

is set to “ON”.

The bobbin thread is almost empty. This message is displayed when the bobbin thread is running out. Follow the

procedure described in “If the bobbin runs out of thread” on page E-23.

The bobbin winder safety device has activated. Is

the thread tangled?

This message is displayed when the bobbin is being wound, and the motor

locks because the thread is tangled, etc.

The carriage of the embroidery unit will

move. Keep your hands etc. away from the

carriage.

This message appears before embroidery unit moves.

The pockets are full. Delete a pattern. This message is displayed when the memory is full and a pattern must be

deleted.

The safety device has been activated. Is the

thread tangled? Is the needle bent?

This message is displayed when the motor locks due to tangled thread or for

other reasons related to thread delivery.

The "Start/Stop" button does not operate with the

foot controller attached. Remove the foot controller.

This message is displayed when the “Start/Stop” button is pressed to sew

Utility stitches or Character/Decorative stitches while the foot controller is

connected.

There is a pattern included that cannot be saved to

USB media. Save the pattern in the machine's

memory.

Depending on the pattern, it may not be possible to save it to a USB flash

drive.

This pattern cannot be used. This message appears when you try to retrieve a pattern that cannot be used

with this machine.

27 This USB media cannot be used. This message is displayed when you try to use incompatible media.

Turn off the power and replace the needle

plate.

This message is displayed when you try to sew with a stitch other than a

straight stitch (middle needle position) while the straight stitch needle plate is

installed.

This message is also displayed when the needle plate is removed while the

machine is still turned on.

29 USB media error This message is displayed when an error occurs with the USB flash drive.

Error messages Cause/solution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Accord BLMCC Seite 198

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Accord BLMCC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info