Bedienungsanleitung Baby Lock Katherine - BL210A (Seite 130 von 140) (Englisch)

661200

130

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Troubleshooting

A-14

Needle breaks.

Screw of the presser foot holder is loose. Securely tighten the screw of the presser foot. B-30

Fabric is too thick.

Use fabric that the needle can pierce when the

handwheel is turned.

B-26, S-4

Fabric is fed forcefully when sewing thick fabric

or thick seams.

Allow the fabric to be fed without being

forcefully pushed.

S-4

Stitch length is too short. Adjust the stitch length. B-37

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13

Upper thread

breaks.

Machine is not threaded correctly (used the

wrong spool cap, spool cap is loose, the thread

did not catch the needle bar threader, etc.)

Rethread the machine correctly. B-19

Knotted or tangled thread is being used. Remove any knots or tangles. –

The selected needle is not appropriate for the

thread being used.

Select a needle that is appropriate for the type

of thread being used.

B-26

Upper thread tension is too tight. Adjust the thread tension. B-38

Thread is tangled.

Use scissors, etc., to cut the tangled thread and

remove it from the race, etc.

A-5

Needle is turned, bent or the point is dull. Replace the needle. B-27

Needle is installed incorrectly. Reinstall the needle correctly. B-27

There are scratches around the opening in the

needle plate.

Replace the needle plate, or consult your

authorized Baby Lock retailer.

A-7

There are scratches around the opening in the

presser foot.

Replace the presser foot, or consult your

authorized Baby Lock retailer.

B-29

There are scratches on the bobbin case.

Replace the bobbin case, or consult your

authorized Baby Lock retailer.

A-2

Using improper needle or thread for the

selected fabric.

Check the “Fabric/Thread/Needle

Combinations” chart.

B-26

While sewing, the thread became knotted or

tangled.

Rethread upper and lower thread. B-13, B-19

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-13

The thread is

tangled on the

wrong side of the

fabric.

Upper threading is incorrect.

Check the steps for threading the machine and

rethread the machine.

Be sure that the presser foot is in the raised

position when threading the machine so that the

upper thread sets properly in the upper tension.

B-19, A-5

Using improper needle or thread for the

selected fabric.

Check the “Fabric/Thread/Needle

Combinations” chart.

B-26

The upper thread is

too tight.

The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-16, A-4

Bobbin thread

breaks.

Bobbin is set incorrectly. Reset the bobbin correctly. B-16

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-13

There are scratches on the bobbin or it doesn’t

rotate properly.

Replace the bobbin. B-16

Thread is tangled.

Use scissors, etc. to cut the tangled thread and

remove it from the race, etc.

A-7

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-13

Symptom Probable Cause Remedy Reference

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baby Lock Katherine - BL210A Seite 130

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Baby Lock Katherine - BL210A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info