661224
104
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
102
APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Troubleshooting
If the machine stops operating correctly, check the following possible problems before requesting service.
If the problem persists, contact your retailer or the nearest authorized service center.
Symptom Probable Cause Remedy Reference
The sewing
machine does
not operate.
The machine is not turned on. Turn on the machine. page 15
The “Start/Stop” button was not
pressed.
Press the “Start/Stop” button. page 42
The presser foot lever is raised. Lower the presser foot lever.
The “Start/Stop button was pressed,
even though the foot controller is
connected.
Do not use the “Start/Stop” button
when the foot controller is
connected. To use the “Start/Stop”
button, disconnect the foot controller.
page 42
The needle
breaks.
The needle is incorrectly installed. Correctly install the needle.
page 32The needle clamp screw is loose.
Use the screwdriver to firmly tighten
the screw.
The needle is bent or blunt. Replace the needle.
The combination of fabric, thread
and needle is not correct.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 30
The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
Attach the presser foot that is
appropriate for the type of stitch that
you wish to sew.
page 94
The upper thread tension is too tight. Loosen the upper thread tension. page 46
The fabric is pulled too much. Lightly guide the fabric.
The spool is incorrectly installed. Correctly install the spool. page 22
The area around the hole in the
needle plate is scratched, or has a
burr on it.
Replace the needle plate.
Contact your retailer or the nearest
authorized service center.
The area around the hole in the
presser foot is scratched, or has a
burr on it.
Replace the presser foot.
Contact your retailer or the nearest
authorized service center.
The bobbin case is scratched, or has
a burr on it.
Replace the bobbin case.
Contact your retailer or the nearest
authorized service center.
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin designed
specifically for this machine.
page 16
104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Baby Lock Tempo - BLTP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Baby Lock Tempo - BLTP

Baby Lock Tempo - BLTP Kurzanleitung - Englisch - 12 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info