661224
105
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
Troubleshooting 103
4
The upper
thread breaks.
The upper thread was not threaded
correctly (for example, the spool is
not installed correctly, the spool cap
is too big for the spool being used, or
the thread has come out of the needle
bar thread guide).
Correct the upper threading. page 22
There are knots or tangles in the
thread.
Remove any knots or tangles.
The selected needle is not appropriate
for the thread being used.
Select a needle that is appropriate
for the type of thread being used.
page 30
The upper thread tension is too tight. Loosen the upper thread tension. page 46
The thread is tangled, for example,
in the bobbin case.
Remove the tangle thread. If the
thread is tangled in the bobbin case,
clean the race.
page 100
The needle is bent or blunt. Replace the needle.
page 32
The needle is incorrectly installed. Correctly install the needle.
The area around the hole in the
needle plate is scratched, or has a
burr on it.
Replace the needle plate.
Contact your retailer or the nearest
authorized service center.
The area around the hole in the
presser foot is scratched, or has a
burr on it.
Replace the presser foot.
Contact your retailer or the nearest
authorized service center.
The bobbin case is scratched, or has
a burr on it.
Replace the bobbin case.
Contact your retailer or the nearest
authorized service center.
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin designed
specifically for this machine.
page 16
The lower
thread is tangled
or breaks.
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 20
The bobbin is scratched or does not
rotate smoothly, or has a burr on it.
Replace the bobbin.
The thread is tangled.
Remove the tangled thread and
clean the race.
page 100
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin designed
specifically for this machine.
page 16
The thread
tension is
incorrect.
The upper thread was not threaded
correctly.
Correct the upper threading. page 22
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 20
The combination of fabric, thread
and needle is not correct.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 30
The presser foot holder is incorrectly
installed.
Correctly install the presser foot
holder.
page 35
The thread tension is incorrect.
Adjust the tension of the upper thread.
page 46
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin designed
specifically for this machine.
page 16
Symptom Probable Cause Remedy Reference
105

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Baby Lock Tempo - BLTP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Baby Lock Tempo - BLTP

Baby Lock Tempo - BLTP Kurzanleitung - Englisch - 12 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info