Bedienungsanleitung BaByliss SH500E (Seite 10 von 72) (Alle Sprachen)

665401

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

16 17

lets you use the appliance for approximately 3 minutes.

• When the screen displays that there are 5 minutes of use remaining (“05”), the

Timer symbol

changes from orange to red and the display of the remaining

use time display  ashes meaning that the appliance needs to be charged (by

placing the appliance in its charging stand).

USE

To start the appliance,

Ensure that the appliance head is perfectly clipped into place before use.

Press the button once.

The cutting length and approximate remaining use time are displayed.

Select the desired cutting length using the + and - buttons.

Press the button a second time.

The motor is on. You can now start using the appliance.

To switch the appliance o , hold down the button for approximately 2 seconds. The cutting

length is set for the next use. Press the

button twice to start the appliance again.

Note:

• The LED display screen switches o automatically after 60 seconds of disuse.

• It is possible to switch the appliance to standby mode by pressing the

button

once.

Tips:

- For your comfort, the appliance can be used in diﬀ erent directions. You can make circular

movements or go backwards and forwards with the appliance over the face and neck. You

will probably need time to get used to the appliance. But quickly, using the appliance will

be comfortable and intuitive.

- If you want to go from a mid-length beard (±15 mm long) to a 3-day beard (approximately

1 mm long), it is advisable to cut it in several steps. For example: to go from a beard of

10 mm in length to one that is 1 mm long, ﬁ rst cut to 6 mm. Then, once this ﬁ rst stage is

complete, cut to 1mm.

- For beards that are longer than 20 mm, it is recommended that you pre-cut your beard to

about 15 mm in length before using the appliance.

- To trim your moustache or your sideburns with precision, ensure that you stretch the skin

of the area to be trimmed and only use one rotating blade.

- To shape clean and precise contours, we recommend the use of a BaByliss beard trimmer

and/or a ﬁ nishing trimmer and/or a shaver.

CLEANING

To clean the appliance thoroughly

Check the appliance is on and press the Cleaning button . The appliance goes into its

cleaning cycle:

The Cleaning symbol lights up on the LED display screen

The appliance head makes 3 back and forth movements to enable any hairs to be

eliminated more easily.

Gently shake the appliance above the sink to remove as much hair and residue as possible.

You can turn on the appliance using the button to increase cleaning e ciency under

running water.

Place the appliance head under running water, alternating the head down and head up,

while the appliance is still running, to e ectively remove all remaining hair. Run the tap water

over all gaps and each of the 3 head openings.

Note

• To extend the time that the appliance is cleaned under running water, you can

press the Cleaning button

twice to start the cleaning cycle again, once the

 rst cycle has ended.

• If you want to stop the cleaning cycle, press the Cleaning button

once to

go back to the last cutting length selected. Clip the head back on to use the

appliance again.

• We recommend cleaning the appliance after each use and before putting it away.

• If the LED display screen shows the Cleaning symbol

when you press the

button, this means that the appliance has not been cleaned following 15

minutes of continuous use. Press the Cleaning button

and clean the appliance

as described above.

• After cleaning, we recommend pressing the Parking button

(see chapter on

storage) to store the appliance.

• We strongly recommend adding a few drops of the oil that came with the

appliance to the blades after use, in order to keep the appliance in optimum

condition.

STORAGE

Check that the appliance is on and press the Parking button .

The Parking symbol is displayed on the LED display screen.

The appliance head unclips and goes back down, taking the combs with it, to go into

the Parking position, which is the ideal position in which to protect the appliance’s

blades and combs before storing.

Note

• If the appliance has not been cleaned before you press the Parking button

, the

Cleaning symbol

 ashes, reminding you to clean the appliance before you

store it.

Then put the still-damp appliance away on its stand.

MEMORY FUNCTION

The appliance has a Memory function that saves the last cutting length chosen.

When the appliance is started up, the combs will automatically return to the last selected

cutting height.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BaByliss SH500E Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info