Bedienungsanleitung Bang Olufsen BeoVision Avant 85 - 2016 (Seite 54 von 120) (Englisch)

704893

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Clip proctection: Each of the audio signal paths also has a peak limiter

protecting its outputs to ensure that the speaker signals are not clipped at high

listening levels. Disabling these peak limiters under Clip protection allow high-

level signal to pass unmodified to the DAC. However, if set to off, some output

signals are clipped and distortion heard, therefore, clip protection should be left

on.

Reset a sound mode

Reset sound settings for the selected sound mode to the default settings.

Speaker groups

Speaker groups – introduction

In the Speaker groups menu, you can make different speaker groups for different

listening positions or loudspeaker combinations. This means that you can use your

speakers differently in different scenarios.

In scenario 1 in the illustration, the right speaker in the top may be set up as a right front

speaker when you watch television from the couch, whereas in scenario 2, the same

speaker may function as a right back speaker when you sit in the armchair listening to

music. The same speaker has different roles in the different speaker groups, and in some

speaker groups, the speaker may not be included.

For each group, you must assign roles to the speakers, set the distance between the

speakers and your listening position and calibrate the speaker level. It is possible to set

distances and speaker levels for each speaker group either manually via the Speaker

groups menu or automatically if you connect a calibration microphone.

In the Speaker groups menu, you can also see if a speaker group has been set for one or

more of the MyButtons.

You access a Speaker group setup menu from the Home menu if you press . Follow

on-screen instructions to create or edit a speaker group. For more advanced speaker

group settings, press  and select Settings, then Sound and set up speaker groups as

described in this chapter.

Create a speaker group

Create a speaker group – introduction

Select a speaker group to set up. You can name the speaker groups or delete groups you

do not want to keep. The Start-up speaker group has a predefined name and you can set

up the group for when you sit in front of the television.

You set distances and speaker levels for each speaker group either automatically if you

connect a calibration microphone or manually via the Speaker distance and Speaker

level menus. A calibration microphone must be purchased separately at your Bang &

Olufsen retailer. For more information, press the red button in the on-screen help and

find 'Assisted speaker calibration', 'Speaker distance' and 'Speaker level'.

Some advanced Bang & Olufsen speakers support preset selection. The preset number is

found in the app for the speaker. You decide which preset should be activated when you

select a speaker group.

To bring up settings for a speaker group, highlight the group and press .

To create a new speaker group, press the green button. The new group has settings

according to the currently playing speaker group. You can change these to your

preferred settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bang Olufsen BeoVision Avant 85 - 2016 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bang Olufsen BeoVision Avant 85 - 2016

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info