Bedienungsanleitung Barbecook Spring 330 (Seite 9 von 346) (Alle Sprachen)

616233

Zoom out

Zoom in

Vorherige Seite

1/346

Nächste Seite

www.barbecook.com 9

• If the regulator has a screw thread, screw the regulator

counter-clockwise on the cylinder (D).

6.5 Replacing the cylinder

1 Close the gas supply and set all control knobs to OFF.

2 Disconnect the empty cylinder and connect the full cylinder.

3 Check the cylinder, the hose and all gas connections for

leaks. See “7 Checking for gas leaks”.

7 CHECKING FOR GAS LEAKS

7.1 Why check for gas leaks?

Propane and butane are heavier than air. As a result, they do not

float away when leaking from the appliance. Especially on

windless days, a leak can cause the gas to collect in and around

the appliance. That accumulated gas can then ignite and

explode.

7.2 When check for gas leaks?

• Before the first use or before the first use after a long period

of non-use.

Also check for gas leaks if your appliance was assembled

by your dealer.

• Each time you replace a gas component.

• At least once a year, preferably at the beginning of the

season.

7.3 Safety instructions

• Put the appliance outdoors, in a well-ventilated area. Make

sure there are no flames or heat sources near the appliance.

• Never use a lighter or match to check for gas leaks.

• Do not smoke and do not light the burners when checking

for gas leaks.

7.4 Which materials do I need?

To check for gas leaks, you need:

• A testing liquid. You can use a ready-made leak spray or a

mixture of water (50%) and dish-washing soap (50%).

• The leak test tool that came with your appliance. You use it

to suck up the testing liquid and apply it to the gas

component or connection that you want to check.

7.5 To check for gas leaks

You check for gas leaks by applying a testing liquid to all gas

components and connections. If the bubbles on a particular

component or connection grow, there is gas leak:

To check for gas leaks, proceed as follows:

1 Put the appliance outside.

2 Get your leak test tool and testing liquid (leak spray or

water/soap mixture).

3 Open the lid and set all control knobs to OFF.

4 Open the gas supply slightly. Turn the valve of the gas

cylinder only once.

5 Suck up some testing liquid with the leak test tool and apply

it to the area that you want to check. You have to check:

• The welds of the gas cylinder (A)

• The hose (B)

• The connections between the cylinder and the pressure

regulator and between the pressure regulator and the

hose (C)

• The connection between the hose and the appliance (D)

Your pressure regulator and coupling may be different

from the ones in the illustrations.

6 Do one of the following:

• If you detect a leak, continue as described in “ In case of

a gas leak”.

• If there are no leaks, close the gas supply, rinse all

components thoroughly with water and dry them well.

7.6 In case of a gas leak

1 Close the gas supply and do one of the following:

• If you detected a leak on one of the connections, tighten

that connection.

C D

✔✖

C D

!gas_spring_standard.book Page 9 Tuesday, July 29, 2014 2:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbecook Spring 330 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info