Bedienungsanleitung Barbecook Spring 330 (Seite 11 von 346) (Alle Sprachen)

616233

Zoom out

Zoom in

Vorherige Seite

1/346

Nächste Seite

www.barbecook.com 11

4 Light the match and hold it about 13 mm from the burner.

5 Set the control knob of one burner to HIGH.

Always light one main burner to start with. Never light all

main burners at the same time.

6 If the burner does not light within 5 seconds, set its control

knob to OFF, close the gas supply and wait 5 minutes. This

allows any accumulated gas to escape.

7 Retry lighting the burner. If it still does not light, refer to

“14 Troubleshooting” to determine the cause of the problem.

8 Once one burner is lit, light the other burners by setting their

control knobs to HIGH.

9.3 Lighting the side burner

This information does not apply to the Spring 300. That appliance

is not equipped with a side burner.

The side burner can only carry vessels with a maximum

weight of 9 kg and a maximum diameter of 220 mm.

9.3.1 USING THE IGNITER

1 Open the lid and set the control knob of the side burner to

OFF.

2 If no other burner is lit yet, open the gas supply and wait ten

seconds. This allows the gas to stabilize.

3 Press the igniter until you hear sparks.

4 While holding the igniter, set the control knob of the side

burner to HIGH.

5 If the burner does not light after three attempts, set its

control knob to OFF, close the gas supply and wait 5

minutes. This allows any accumulated gas to escape.

6 Retry lighting the side burner. If it still does not light, try

lighting it with a match or refer to “14 Troubleshooting” to

determine the cause of the problem.

9.3.2 USING A MATCH

1 Place a match in the match holder.

2 Open the lid and set the control knob of the side burner to

OFF.

3 If no other burner is lit yet, open the gas supply and wait ten

seconds. This allows the gas to stabilize.

4 Light the match and hold it about 13 mm from the side

burner.

5 Set the control knob of the side burner to HIGH.

6 If the side burner does not light within 5 seconds, set its

control knob to OFF, close the gas supply and wait 5

minutes. This allows any accumulated gas to escape.

7 Retry lighting the side burner. If it still does not light, refer to

“14 Troubleshooting” to determine the cause of the problem.

9.4 Switching the burners off

If you no longer use the burners, you have to switch them off.

Proceed as follows:

1 Close the gas supply.

2 Set the control knobs of the burners to OFF.

By closing the gas supply first, you make sure there is no

gas left in the appliance.

9.5 Relighting the burners

If a burner goes out while in use, proceed as follows:

1 Open the lid and close the gas supply.

2 Set all control knobs to OFF and wait 5 minutes. This allows

any accumulated gas to escape.

3 Relight the burner(s).

9.6 Checking the flames

Each time you light a burner, you have to check its flames. A

perfect flame is almost completely blue, with some yellow at the

top. Sporadic yellow flames are normal and not harmful.

If there is something wrong with the flames, do one of the

following to solve the problem:

!gas_spring_standard.book Page 11 Tuesday, July 29, 2014 2:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbecook Spring 330 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info