Bedienungsanleitung Basetech 2147832 (Seite 4 von 8) (Deutsch, Englisch, Holländisch, Französisch)

738487

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

e) Work safety

• Ensure that there is sufcient lighting.

• Ensure proper ventilation during soldering. Solder and ux vapours can be harmful

to your health.

• Wash your hands thoroughly after working with solder. This is particularly

important when using lead-based solder.

• Do not put soldering alloys into your mouth. Do not eat or drink during soldering.

• Wear suitable protective clothing and safety goggles when soldering. Liquid/

splashing solder may cause serious burns or eye damage.

Operating elements

5 6 7 8

1 450 ºC preset button

2 300 ºC preset button

3 200 ºC preset button

4 LCD display

5 Tip holders

6 Spare tips

7 Solder spools

8 Power switch

I/O (ON/OFF)

9 + button (increase

working temp.)

10 - button (decrease

working temp.)

11 Power plug

12 Soldering tip

13 Handle

14 Soldering iron holder

15 Tray for sponge

16 Sponge

Setting up

a) Soldering iron tips

Risk of burns! Allow the tip to cool down before attempting to replace it. Do not

overtighten the tip.

• Pointed tip: Used for point soldering and thin

wires.

• Flat tip: Used for light electrical work.

• Store any unused tips in the tip holder (5).

b) Preparing the sponge

Place the sponge (16) into the tray (15) and moisten it slightly before use.

Operation

Always keep the tip tinned before switching off or storing for any period of time.

Do not keep the iron on for an extended period of time as this will break down the

surface of the tip.

• Connect the power plug (11) to a mains power outlet.

• Turn the power ON: Flip the power switch (8) to the [ I ] position.

The LCD display (4) shows the preset target temperature for a few seconds, followed by the

actual working temperature of the soldering tip (12).

• Select the required working temperature by:

- Pressing one of the preset buttons (1), (2), or (3).

- Pressing the temperature increase [+] (9) or decrease button [-] (10).

The temperature can be adjusted in 10 °C increments. The working temperature

range is 200 to 450 °C.

• Turn the power OFF: Flip the power switch to the [O] position.

• Disconnect the power plug (11) from the mains power outlet, and allow the soldering iron to

completely cool down before storing away.

Troubleshooting

Problem Suggestion

Soldering iron does

not heat up.

Check that the mains supply (socket) functions correctly. The

mains cable or power source may be faulty. Seek advice from an

electrician if needed.

Tip does not get hot

enough.

• Let the tip cool down completely and check that it is screwed in

completely.

• The tip may be faulty, try using a different one.

Maintenance and care

• Never clean the tip with coarse, abrasive materials like les.

• If oxide forms on the tip, lightly rub with abrasive paper, wipe clean, then immediately reheat

and re-tin the tip to prevent oxidation of the wettable surface.

• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as

they can cause damage to the housing and malfunctioning.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product in accordance

with applicable regulatory guidelines.

You thus fulll your statutory obligations and contribute to the protection of the

environment.

Technical data

Input voltage / current ................... 230 V/AC 50 Hz,

Power consumption ...................... 60 W

Temperature range ....................... 200 - 450 ºC

Temperature adjust ....................... 10 ºC increments

Solder ........................................... ø1 mm 10 g (lead-free ux core)

ø1.5 mm 10 g (lead-free ux core)

Protection class ............................ I

Operating conditions ..................... 0 to +45 ºC, 35 – 80 % RH (non-condensing)

Storage conditions ........................ 35 to +80 ºC, 35 – 80 % RH (non-condensing)

Dimensions ................................... Main unit: 125 x 95 x 150 mm (W x H x D)

Stand: 215 x 90 x 95 mm (W x H x D)

Soldering iron: ø36 x 260 mm

Weight .......................................... 1.1 kg (net)

Visit the Conrad website and search Item No.: 2147832 for information about any

optional accessories, spares, or replacement parts.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights

including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication

represent the technical status at the time of printing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Basetech 2147832 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info