Bedienungsanleitung Batavia BT-CRH001 - 7062511 (Seite 7 von 17) (Deutsch, Englisch, Holländisch, Französisch)

758257

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

English

12 13

English

• Always use the auxiliary handle supplied

with the tool.

• Do not place pressure on the tool – to do

so could shorten its service life.

• Drill bits become hot during operation.

Allow to cool prior to handling.

• If you are interrupted when operating the

drill, complete the process and switch off

before diverting your attention elsewhere.

• Always disconnect the SDS drill from the

electric supply before changing a chisel or

drill bit.

• Examine the chuck regularly for signs of

wear or damage. Have damaged parts

repaired by a qualied service centre.

• Always wait until the drill has come to a

complete stop before placing it down.

• On completion of the work, disconnect the

tool from the power source and remove

the chisel/bit from the machine.

• Periodically check all nuts, bolts and other

xings and tighten where necessary.

• Visibly check the tool after use, especially

the power cable, which can be damaged

by sharp masonry.

• Always t the dust guard to the bit in use

to prevent damage from debris entering

the SDS chuck.

• If operating the tool causes discomfort in

any way, stop immediately and review your

method of use.

DURING USE

• Hold power tool by insulated gripping

surfaces (7), when performing an opera-

tion where the cutting accessory or fas-

tener may contact hidden wiring (cutting

accessory and fasteners contacting a

“live” wire may make exposed metal parts

of the power tool “live” and could give the

operator an electric shock)

• In case of electrical or mechanical mal-

function, immediately switch off the tool or

unplug charger from power source.

BEFORE FIRST USE

Remove the machine and the accessories from

the packaging. Check the machine for trans-

port damage and do not use the machine in

case of damages. Keep the packing materials

away from children, risk of suffocation!

INTENDED USE

The SDS Plus Hammer drill is designed for

drilling masonry. Also capable of drilling wood

and metal with the optional purchase of a

standard chuck with SDS Plus connector. The

equipment is to be used only for its prescribed

purpose.

OPERATION

Auxiliary Handle

• The auxiliary handle (13) should always be

used when drilling.

• The auxiliary handle (13) can be rotated

360° around the drill head, enabling safe

and comfortable operation for both left

and right-handed users.

To adjust the auxiliary handle:

1. Rotate the grip anti-clockwise. This will

loosen the handle assembly.

2. Move the side handle to the required

position.

3. Secure in position by rotating the grip

clockwise.

Depth Stop

1. Rotate the grip anti-clockwise. This will

loosen the handle assembly.

2. Move the depth stop (18) to the required

position.

3. Secure in position by rotating the grip

clockwise.

Operating the Chuck

• This rotary hammer has a chuck designed

for SDS Plus drill bits.

• The SDS Plus system allows bits to be

inserted with a simple push-t action.

• Always grease the tail end of SDS bits.

Bits should be freshly greased and free

from dirt and dust before use.

Inserting a Drill Bit

1. Pull back the chuck collar (15) and hold.

2. Insert SDS Plus drill bit (17) fully into the

chuck (16). Use a twisting motion to line

up the grooves in the accessory.

3. Release the chuck collar.

4. The bit should now be locked into the

machine. Check by pulling the bit; if the bit

can be removed, repeat the above

procedure until secure.

• To remove a bit from the chuck, pull the

chuck collar back, and pull rmly on the

drill bit.

WARNING: Never t any attachment with a

maximum speed lower than the no load speed

of the machine.

Hammer Selection

• The rotary hammer can be used in either

hammer drill mode (for masonry work), or

conventional rotary drill mode (for wood,

metal, plastics etc.) with the optional pur-

chase of a standard chuck to SDS Plus

adaptor.

• To select hammer drilling mode, depress

the mode selector release button (2) on

the mode selector (1) and align the mode

selector with the „ “ symbol.

• To select rotary drilling mode, depress the

button on the mode selector release

button on the mode selector and align the

mode selector with the „ “ symbol.

• Do not attempt to move the mode selector

whilst the rotary hammer is running.

OPERATING INSTRUCTIONS

IMPORTANT: Put on all safety equipment

required before you operate this drill.

Trigger Switch

• Always hold the rotary hammer rmly

using both hands.

• To start the rotary hammer, squeeze the

trigger switch (8).

• To stop the rotary hammer, release the

trigger switch.

Selecting forward or reverse rotation

• The direction of the drill can be changed

using the forward/reverse switch (6).

• To run the drill in a clockwise direction,

position the forward/reverse switch on the

left, adjacent to the „►“ symbol.

• To run the drill in an anti-clockwise

direction, position the forward/reverse

switch on the right, adjacent to the

„◄“ symbol.

• Do not attempt to move the forward/

reverse switch whilst the rotary hammer is

running.

• Do not attempt to run the rotary hammer

with the forward/reverse switch in mid

position.

Speed Control

• The speed of the rotary hammer is

controlled by the pressure applied to the

trigger switch (8). The further the trigger is

depressed the higher the speed.

Gear Selection

• Select gear 1 on the gear switch (3) for the

low speed, high torque gear. Suitable for

low speed drilling and driving screws and

fasteners.

• Select gear 2 on the gear switch for the

high speed, low torque gear. Suitable only

for high speed drilling.

Note: Always read the documentation

provided with drill bits and accessories for the

recommended or maximum speed setting and

use the most appropriate gear. See ‘Technical

Data’ for the maximum no load speed of each

gear.

Drilling Concrete

• Using hammer drill mode, apply pressure

to the rear of the rotary hammer, in line

with the drill bit.

• For efcient drilling, it is advisable to use

TCT (tungsten carbide tipped) drill bits.

Ensure that drill bit size is within the

maximum capacity of the rotary hammer

(see ‘Technical Data’).

• Do not apply too much pressure if debris

blocks the drill hole. Run the rotary

hammer slowly, and remove the bit from

the hole. Repeat until hole is cleared.

ACCESSORIES

Use only accessories with an allowable speed

matching at least the highest no-load speed of

the tool.

Batavia BT-CRH001 - 7062511 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info