Bedienungsanleitung Batavia BT-CS015 - 7062848 (Seite 12 von 50) (Deutsch, Englisch, Holländisch, Französisch)

758290

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

English

8. Before the rst use

Remove the machine and all accessories

from the package. Keep the packaging

materials out of the reach of small children.

There is a danger of suffocation!

9. Contents of packing

1× Circular Saw

1× Saw blade on saw

1× Rip fence

1× Vacuum hose adapter

1× Allen key

1× Instruction manual

10. Intended use

Electric circular saw suitable for cross, rip

and bevel cutting of hard and softwood

timber and sheet material

11. Assembly and adjusting

instructions

Before adjusting the saw, make

sure the plug is removed from the

socket.

11.1 Setting the sawing angle (bevel)

• Loosen both knobs (6, 15).

• Rotate the soleplate to the correct posi-

tion (0° - 45°), and tighten the knobs.

The sawing angle (bevel) can be read

on the scale for mitre angle (5).

11.2 Fitting the ripfence

• Loosen knob (7).

• Insert the rip fence into the slots

provided.

• Set the correct cut width and tighten

the knob (7).

11.3 Setting the cutting depth

• Loosen knob (18).

• Move the soleplate (17) downwards.

• The cut depth of the saw blade can be

read off on the side of the safety guard.

• Tighten the clamping knob (18) once

the correct depth is set.

11.4 Exchanging or cleaning the saw blade

Before any maintenance work always switch

off the plunge saw and disconnect from

mains power.

• Press and hold the spindle lock (19)

down.

• Use the hex key (21) to turn the screw

(11) at the saw blade slightly clockwise

or counter-clockwise until the spindle

clicks into place.

• Use the hex key to loosen the screw

counter-clockwise.

• Turn the safety guard to the rear, and

hold it there with the aid of the knob

(12). Withdraw the retaining ring and

the saw blade, and clean the saw blade,

or replace it with a new one.

• Again place the saw blade back on the

shaft. Allow the safety guard to return

over the saw blade by releasing the

knob (12).

Note: The rotation direction arrows of

saw blade and saw must be aligned!

• Replace the outer flange in such way

that the slaving pins sit in the recesses

of the inner flange.

• Press and hold the spindle lock and

tighten the screw.

12. Operation

Use of hearing protection is

recommended while operating the

circular saw.

12.1 Switching On/Off

• Press knob (14) with your right-hand

thumb and keep it depressed.

• Press knob (13) to start the saw.

• Release knob (13) to stop the saw.

12.2 Operation

• Hold the work using clamps or a vice to

have both hands free to operate the saw.

• Switch on the saw and place the bot-

tom plate on the work.

• Firmly press the bottom plate on the

work, otherwise the circular saw may

start to vibrate, causing the blade to

break more easily.

Let the saw do the job. Do not put

undue pressure on the circular saw.

7062848-Circular_Saw_1400W-Ma-1803-19.indb 10 20-03-18 10:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CS015 - 7062848 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info