Bedienungsanleitung Batavia BT-CS015 - 7062848 (Seite 11 von 50) (Deutsch, Englisch, Holländisch, Französisch)

758290

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

English

• Be careful when cutting wood with

knots, nails or cracks in it and/or dirt on

it, as these can cause the blade to get

stuck.

• Never leave the circular saw

unattended.

• Use this circular saw to saw only wood

or wood-like products.

5. Using the machine

• Use clamps or a vice to hold the work.

• Never remove wood chips and saw dust

that is close to the saw blade with your

hands. If there are small pieces of wood

left between the xed and the movable

parts, the circular saw will have to be

stopped. The plug needs to be removed

from the socket, before any left piece

can be removed.

• Check that the blade is suitable for the

spindle speed of the circular saw. Do

not attempt to cut before the circular

saw has reached full speed. Make sure

the circular saw runs without load (i.e.

is not in contact with the work) when

you switch it on. The circular saw must

have reached its full speed rst.

• Never cut wood that is thicker than the

depth of the saw blade.

• When cutting in wooden walls or floors,

check there is no wiring or piping where

you intend to cut.

• Switch off the tool and wait until the

blade has stopped completely before

moving the saw away from the work or

putting it down. Hearing protection

should be worn when using circular

saw.

Switch off the machine immediately when

you discover:

• A defective mains plug or mains lead;

• A defective switch.

• Overheating of the circular saw.

• Smoke or odour caused by scorched

insulation.

6. Laser

6.1 Safety instructions for the laser cut-

ting guide

a. Do not point the laser beam at persons

or animals and do not look into the

laser beam. This laser emits a laser

beam that falls under laser class 2 in

accordance with EN 60825-1:2014. You

could blind people with it.

b. A laser is not a toy and does not

belong in the hands of children. Using

it incorrectly may result in irreparable

damage to the eyes.

c. It is forbidden to manipulate the laser

so as to increase its power in any way.

No liability will be assumed for any

damages caused as the result of fail-

ure to comply with these safety

instructions.

d. The laser does not contain any ser-

viceable parts. Therefore, do not open

the housing. Otherwise, you will ren-

der the warranty void.

e. Warning! Do not swap the laser with

another type of laser. Only the manu-

facturer of the laser or an authorised

representative may perform repairs.

f. Do not point the laser beam towards

highly reflective surfaces.

g. Do not insert any hard objects in the

laser optics.

h. Clean the laser optics with a soft, dry

cloth.

7. Electrical safety

Always check that the voltage of

the power supply corresponds to

the voltage on the rating plate.

• Do not use the machine if the mains

cable or the mains plug is damaged.

• Only use extension cables that are suit-

able for the power rating of the machine

with a minimum thickness of 1.5 mm2.

If you use a extension cable reel, always

fully unroll the cable.

7062848-Circular_Saw_1400W-Ma-1803-19.indb 9 20-03-18 10:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CS015 - 7062848 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info