Bedienungsanleitung Batavia BT-CT001 - 7063419 (Seite 12 von 46) (Deutsch, Englisch, Holländisch, Französisch)

758282

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

12.3 Assembling a cutting / sanding disc

(See g. C)

Unscrew the small screw (a) on top of man-

drel, then insert an appropriate cutting/

sanding disc into mandrel and lightly tighten

(a) with wrench. Do not

over-tighten, or the cutting/ sanding disc

may crack.

12.4 Assembling felt wheel or tip

(See g. D)

The felt wheel or tip should be screwed on

the mandrel.

12.5 Assembling a sanding drum

(See g. E)



(a) on top of the sanding drum

shank. Slide the sanding drum onto the

(a)

again.

12.6 Installation of auxiliary handle

You can use the machine with or without

auxiliary handle. Therefore, use proper

guard (3)

Depending on the work ahead it is recom-

mended to use auxiliary handle and hold the

machine with both hands.

Disconnect the power tool from power

supply.

• Unscrew and remove the guard (3).

• Put auxiliary handle (1) on the machine.

• Install and tighten appropriate guard

(3).

12.7 Installation of exible shaft

Before assembly always remove

the plug from the mains!

• Loosen and remove front plastic guard

(3) (g. G).

• Pull some of the cord (a) (g. H) from

(11) so its end can be

installed in the collet nut (b) (g. H).

• Press and hold spindle lock button (4).

• Tighten the collet nut (2) with the sup-

plied wrench.

• 

shaft (11).

• 

the positioning nut (g. I).

12.8 Installation and replacement of acces-

sories in exible shaft holder

(g. F)

Before assembly always remove

the plug from the mains!

• 



shaft spindle locking.

• (a).

• Insert the accessory into the collet that

matches the shank size of the

accessory.

• Tighten the collet nut (a) with the sup-

plied wrench.

• 

spindle locking (b).

13. Switch on/off

To turn on the machine, press the “I” side of

the ON/OFF switch (9). To turn off the

machine, press the “0” side of the ON/OFF

switch(9).

14. Speed setting

The tool has a variable speed selector (6)

for precise speed adjustment numbered “8”

to “35”. The speed can be adjusted from

8,000 to 35,000 min-1.

Always choose the correct speed range for

your work according to the material.

Determine the correct speed for work on

any material by practicing on a piece of

scrap.

14.1 Adjustment of the speed

• After setting the switch (9) position to ‘I’

you can change spindle rotational

speed by choosing appropriate number

shown on the display (6) range from 8

to 35.

• You can change rotational speed by

(7).

• Press the button ‘+’ (many times if

needed) to increase speed.

• 

needed) to decrease speed.

Choose a low speed when working with

wood, plastics and polishing.

7062854-Compact-Tool-170W-Ma-1803-27.indb 10 14-05-18 10:20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CT001 - 7063419 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info