Bedienungsanleitung Batavia Racer BT-CS006 (Seite 23 von 60) (Deutsch, Englisch, Holländisch, Französisch)

589450

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

c) Avoid the area in front of and behind a

rotating cutting wheel. A kickback will send

the electric power tool in the opposite direction

to the movement of the grinding disc at the

point where it jams.

d) Work extremely carefully in the

neighbourhood of corners, sharp edges

etc. Prevent the tool insert from recoiling

from the workpiece and jamming. The

rotating tool insert bends at corners and sharp

edges or if it rebounds and may jam itself. This

causes a loss of control or kickback.

e) Do not use any chainsaw or toothed saw

blade, nor any segmented diamond disc,

with slots wider than 10 mm. Such tool

inserts frequently cause a kickback or loss of

control of the electric power tool.

f) Avoid jamming of the cutting wheel or too

high a contact pressure. Do not make

excessively deep cuts. An overload of the

cutting wheel increases its stress and its

susceptibility to tilting or jamming and, hence,

increases the possibility of a kickback or break

in the grinding wheel.

g) If the cutting wheel becomes jammed or if

you interrupt the work, switch the device

off and keep it held gently until the disc

has come to a standstill. Never attempt to

remove a still-running cutting wheel from

the cut, otherwise kickback may result.

Find and remove the cause for the jamming.

h) Do not switch on the electric power tool

again, while it is still in the workpiece.

Allow the cutting wheel to rst reach its full

rotation speed before carefully continuing

the cut; otherwise, the disc may snag, jump

out of the workpiece or cause a kickback.

i) Provide support for large workpieces, to

reduce the risk of a kickback through

jamming of the cutting wheel.

Large

workpieces can bend under their own weight.

The workpiece must be supported on both sides

of the disc, as well as both in the neighbourhood

of the separation cut and at the edges.

j) Be especially careful when making "pocket

cuts" in existing walls or other non-visible

areas. The immersed cutting tool can cause a

kickback when cutting into gas or water pipes,

electric cables or other objects.

2.7 SAFETY AND OPERATING INSTRUCTIONS

FOR DIAMOND GRINDING WHEELS

Use

Only use the cut off grinding disc for cut off

grinding and not for rough grinding! Only use the

cut off grinding discs for the materials indicated

and not for any other materials. Risk of injury!

Cutting and cooling!

General Information

This tool insert is fragile, therefore extreme care

is required when handling it. The use of damaged

and incorrectly tensioned or installed tool inserts

is dangerous and can result in serious injury.

Handling and storage

Tool inserts must be carefully handled and

transported. Tool inserts should be stored in such

a way that they are not exposed to any

mechanical damage or damaging environmental

inuences.

To avoid damage, remove the tool insert before

transporting an electric power tool.

Selection and safe and proper use

Pay attention to the data on the label or on the

tool insert, such as the restrictions on use, safety

instructions or other advice. Do not alter the

characteristic direction of motion of the tool insert.

If there is ambiguity over the selection of tool

inserts, contact the manufacturer or a specialist.

Adhere to the permissible rotation speeds for the

tool insert and the electric power tool.

Before use

Tool inserts must be given a visual inspection

before each start-up. Do not use damaged tool

inserts. Secure the piece to be worked on.

Inserting and changing

Tighten the tool inserts in accordance with their

instructions and those of the electric power tool's

manufacturer. The tightening of tool inserts should

onlybeundertakenbyqualiedpersons.After

each tightening, carry out a test run for a suitable

length of time, during which the characteristic

maximum working speed of the tool insert may

not be exceeded.

Always tighten tool inserts without introducing any

out-of-roundness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia Racer BT-CS006 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info