Bedienungsanleitung Bauknecht BU 1760C FT (Seite 6 von 9) (Englisch)

806808

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

ACCESSORIES

POTS AND PANS

Only use pots and pans made from ferromagnetic

material which are suitable for use with induction hobs:

• enamelled steel

• cast iron

• special pots and pans in stainless steel, suitable

for induction cooking

To determine whether a pot is suitable, check for the symbol (usually

stamped on the bottom). A magnet may be used to check whether pots are

magnetic.

The quality and the structure of the pot base can alter cooking performance.

Some indications for the base's diameter do not correspond to the actual

diameter of the ferromagnetic surface.

Some pots and pans have only a part of the bottom in a ferromagnetic

material, with parts in another material that is not suitable for induction

cooking. These areas may heat up at dierent levels or lower temperatures.

In certain cases, where the bottom is made mainly of non-ferromagnetic

materials, the hob might not recognize the pan and therefore not switch

on the cooking zone.

To ensure optimum eciency, always use pots and pans with a at bottom

that distributes the heat evenly. If the bottom is uneven, this will aect

power and heat conduction.

NOOK

Empty pots or pots with a thin base

Do not use empty pots or pans when the hob is on. The hob is equipped with

an internal safety system that constantly monitors the temperature, activating

the “automatic o“ function where high temperatures are detected. When

used with empty pots or pots with thin bases, the temperature may rise very

quickly, and the “automatic o“ function may not be triggered immediately,

damaging the pan or the hob surface. If this occurs, do not touch anything,

and wait for all components to cool down.

If any error messages appear, call the service centre.

Minimum diameter of pot/pan base for the dierent cooking areas

To ensure that the hob functions properly, use pots of a suitable minimum

diameter (refer to the table below).

Always use the cooking zone that best corresponds to the minimum

diameter of the bottom of the pot.

Place the pot making sure it is well centered on the cooking zone in use.

It is recommended not to use pots that exceed the perimeter of the cooking

zone in use.

100 mm 120 mm

200

mm150 mm

ø min.

ADAPTER FOR POTS/PANS UNSUITABLE FOR INDUCTION

Using this accessory makes it possible to use pots and pans that are not

suitable for induction hobs. It is important to bear in mind that using it

aects eciency and, consequently, the time needed to heat food. Its

use should be limited because the temperatures reached on its surface

depend signicantly on the pot/pan used, its atness, and the type of food

being cooked. Using a pot or pan with a smaller diameter than the adapter

disc may cause heat to build up that is not transmitted to the pot or pan,

which could blacken both the hob and the disc. Adapt the diameter of

your pots/pans and the hob to the diameter of the adapter.

DAILY USE

POSITIONING

Locate the desired cooking zone by referring to the position symbols.

Do not cover the control panel symbols with the cooking pot.

Please note: In the cooking zones close to the control panel, it is advisable to

keep pots and pans inside the markings (taking both the bottom of the pan

and the upper edge into consideration, as this tends to be larger).

This prevents excessive overheating of the keypad. When grilling or frying,

please use the rear cooking zones wherever possible.

ACTIVATING/DEACTIVATING COOKING ZONES AND ADJUSTING POWER

LEVELS

The oven control panel features 4 adjustable knobs for cooktop operation.

The numerical scale on the cooktop control knobs corresponds to dierent

power levels.

0 9 8 7 6 5 4 3 2 1

To activate the cooking zones:

After positioning the pot on the chosen cooking zone, select the required

power level by turning the knob clockwise. Each cooking zone has dierent

heat settings, ranging from "1" (minimum power) to "9" (maximum power).

When a knob is set to a power level between 1 and 9, the cooktop indicator

light switches on.

The display will show the level as per knob position, and the value shown

will be updated according to knob rotation.

Power indicator display

Selected cooking zone indicator

IMPORTANT: When the "0" on the cooktop control knob corresponds with

the "

" symbol on the oven control panel, there are no corresponding

functions; therefore, the cooking zone switches o.

IMPORTANT: if the pot is not suitable or not correctly positioned on the

cooking zone, the

“ ”

symbol will ash on the display. If, within one minute, a

suitable pot is not used or the pot is not correctly positioned, the

“ ”

symbol

will appear permanently on the display. At this point, in order to reactivate

the cooking zone it will be necessary to turn the corresponding oven knob

to “0” and then select the desired power level.

FIRST TIME USE

At the rst switch on, all the oven knobs must be in the “0” position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht BU 1760C FT Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht BU 1760C FT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info