Bedienungsanleitung Bauknecht GTE508 (Seite 3 von 4) (Englisch)

703659

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

5. All LEDs are o and the product is working.

• Contact the After-Sales Service.

6. The compressor runs continuously.

• Have hot foods been put in the appliance?

• Has the appliance lid been left open for a long

time?

• Is the appliance placed in a very warm room or

near heat sources?

• Has the fast freeze function been activated? (the

green LEDS ash alternatively)

7. Too much ice on the upper edge.

• Are the defrost water drainage plugs correctly

positioned?

• Is the appliance lid properly closed?

• Is the appliance lid seal damaged or deformed?

(See chapter “Installation”)

• Have the 4 protection pieces been removed?

(See chapter “Installation”)

8. Formation of condensate on the external walls

of the appliance.

• It is normal for condensation to form under

certain atmospheric conditions (humidity above

85%) or if the appliance is located in a damp or

poorly ventilated room. The performance of the

appliance is in no way aected.

9. The layer of ice on the internal walls of the

appliance is not uniform.

• This phenomenon is quite normal.

AFTER-SALES SERVICE

Before contacting After-Sales Service:

1. See if you can solve the problem yourself.

2. Switch the appliance on again to see if the problem

has been solved. If it has not, disconnect the

appliance from the power supply and wait for about

an hour before switching on again.

3. If the problem persists after this course of action,

contact After-Sales Service.

Specify:

• the nature of the fault,

• the model,

• the service number (the number after the word

SERVICE on the rating plate on the rear of the

appliance)

• your full address,

• your telephone number and area code.

ELECTRICAL CONNECTION FOR GREAT BRITAIN AND IRELAND ONLY

Warning – this appliance must be earthed.

Fuse replacement

If the mains lead of this appliance is tted with a BS 1363A 13amp fused plug, to change

a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as

follows:

1. Remove the fuse cover (A) and fuse (B).

2. Fit replacement 13A fuse into fuse cover.

3. Ret both into plug.

Important:

The fuse cover must be retted when changing a fuse and if the fuse cover is lost the

plug must not be used until a correct replacement is tted.

Correct replacement are identied by the colour insert or the colour embossed in words

on the base of the plug.

Replacement fuse covers are available from your local electrical store.

For the Republic of Ireland only

The information given in respect of Great Britain will frequently apply, but a third type of plug and socket is also used, the 2-pin,

side earth type.

Socket outlet / plug (valid for both countries)

If the tted plug is not suitable for your socket outlet, please contact After-sales Service for further instruction.

Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualied technician in compliance

with the manufactures instructions and current standard safety regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht GTE508 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht GTE508

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info