53098

Bauknecht WAK7990 Seite 11

11
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
63
Fault display table
a.Fault in the water supply
The appliance has no or insufficient water supply.
For models with a fault display, the “Water tap” lamp
lights up and (depending on model) the spin speed
indication lamps flash.
For models with no fault display, the washing machine
stops in the appropriate programme step.
Switch the appliance off and pull out the mains plug.
Check whether:
•
the water tap is fully turned on, and the water
supply pressure is sufficient
•
the water inlet hose is kinked
•
the water connection mesh filters are blocked
(see “Care And Maintenance”/”Mesh Filters in the
Water Connection”)
•
the water supply hose is frozen up
•
the washing machine has a safety hose and the
safety valve is open (red indicator in the safety valve
inspection window); In this case replace it with a
new safety hose
Reconnect the appliance to the electrical socket.
For models with a fault display, reselect the desired
programme and start it.
For models without a fault display continue the
programme by pressing the “On/Off” or the “Start” or
the “Start/Pause” button (depending on model) again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
b.Draining fault
Waste water not pumped out.
For models with a fault display the spin speed indication
lamps flash and the pump display flashes. If a digital display
is fitted, “P
” and “F” are also displayed alternately.
For models with no fault display, the washing machine
stops in the appropriate programme step.
Switch the appliance off and pull out the mains plug.
Check whether:
•
the drain hose is kinked
•
the pump or the filter is blocked (see “Removing
The Filter”)
IMPORTANT:
before draining, make sure that the
water has cooled down.
•
The water in the drain hose is frozen up
Reconnect the appliance to the electrical socket.
For models with fault display, select and start the
“Drain” cycle.
To rinse the laundry, we then recommend a short
programme without the addition of detergent.
For models without a fault display continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
c. Fault in an electrical component
The appliance stops in the middle of a programme.
For models with a fault display, the spin speed
indication lamps flash. If a digital display is fitted, “F4
” to
“F16
” are also displayed.
Switch the washing machine off. First of all select and
start the “Drain” cycle.
Then select and start the desired programme again.
For models with no fault display, the washing machine
stops in the appropriate programme step.
First switch the washing machine off and on again to
continue with the programme.
If the fault persists, please contact After-Sales Service
(see “After-Sales Service”).
d.“Water Stop” fault
(if fitted)
The “Water Stop” fault may have been triggered by:
1.
excess foaming
2.
a leak in the washing machine.
In this case the pump is switched on automatically in
order to pump the water out.
For models with a fault display, the “Water Stop”
indication flashes and the spin speed indication lamps
flash. If a digital display is fitted, “A
” and “F” are also
displayed alternately.
For models with no fault display, the washing machine
stops in the appropriate programme step.
Switch the appliance off, pull out the mains plug
and turn the water tap off.
Tilt the appliance forwards ( with 2 people it is
suggested), to allow the collected water to flow out
from the bottom of the appliance.
Then:
1.
Plug in the appliance.
2.
Turn the water tap on (if water immediately flows
into the appliance again, without the appliance being
started, there is a fault. Turn off the tap and notify
After-Sales Service).
3.
For models with fault display, select and start the
desired programme again.
For models with no fault display, continue the
programme by pressing the “On/Off” button again.
If the fault occurs again, please contact After-Sales
Service (see “After-Sales Service”).
Luminous display
Spin
speed
lights
Digital display
(if fitted)
Fault description
“Water tap” flash “H” and “F” “Fault in water supply”
“Pump” flash “P” and “F” “Draining fault”
- flash from “F4” to “F16” “Fault in an electrical component”
“Water Stop” flash “A” and “F” “Water Stop fault”
4GB05140.fm Page 63 Wednesday, April 14, 2004 12:18 PM
Black process 45.0° 100.0 LPI
… 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bauknecht WAK7990 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info