Bedienungsanleitung BeamZ 151.325 BAC504 ProPar (Seite 6 von 32) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

766832

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

MANUAL Mode

1. Press <MANUAL> on the remote controller.

2. Press <R>, <G>, <B>, <W> (red, green, blue, white) to choose your colour.

3. Press again <R>, <G>, <B>, <W> (red, green, blue, white) to close your colour.

4. Press <+> or <–> to either increase or decrease the percentage of each colour.

FADE/UNIT Mode

To adjust the FADE speed of the automatic program, the sound active program and the manual mode.

1. Press <FADE> on the remote controller.

2. Press <FADE> again to turn off the Fade mode.

NUMBER 1~9

To adjust the brightness value of the automatic program, the Sound active program and Manual Mode.

Press digit <1> to <9> to change different brightness on the device.

The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery

contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil

from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not

possible.

If the range of the remote control decreases, replace the battery. For this purpose, on

the rear side of the remote control press the small bar with the groove to the right (1)

and at the same time remove the battery support (2). For operation, one 3 V button

cell type CR 2025 is required. When inserting, pay attention that the positive pole of

the button cell shows upwards in the support.

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.

Procedure: Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding

can cause greater accumulation of dirt on the unit’s optics.

• Make sure the area below the installation place is free from unwanted persons during servicing

• Housings, fixations and installations spots( ceiling, truss, suspensions) should be totally free from any deformation

• The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is

detected

• In order to protect the fixture from overheat the cooling fans (if any) and ventilation openings should be cleaned

monthly.

• The interior of the fixture should be cleaned annually using a vacuum cleaner or air-jet.

• Clean with soft cloth using normal glass cleaning fluid.

• Always dry the parts carefully.

• Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.

ATTENTION: We strongly recommend internal cleaning to be carried out by qualified worker!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ 151.325 BAC504 ProPar Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info