Bedienungsanleitung BeF Home Passive - HOT AIR FIREPLACE INSERTS (Seite 5 von 9) (Englisch)

810623

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

________________________________________________________________________________________________________________________________

Firma: BeF Home, s.r.o. Strana 5 (celkem 9) Platí od: 1. 4. 2014

Vydání: 4

Required brick veneer and thermal insulation:

Minimal thermal insulation of protected building panels was defined during the test of fireplace insert in accordance with EN 13229. During

the test the thermal insulation made of cellular calcium-silicate slabs was used ρ = 250kg/m3 . It is necessary to use this kind of material in the

prescribed minimal thickness. Other insulation materials must be of the same or lower thermal conductivity and a comparable thermal

resistance! - Brick veneer: a 10 cm thick mineral brick veneer must be made exactly on the protected building wall (back wall, where

appropriate side wall). The brick veneer must abut onto the insulation layer and on the protected building side. It must over-lap the connecting

piece (venting) upwards by at least 20 cm. The insulation brick veneer is not necessary when the building wall is 10 cm thick at least and is not

made of combustible material and it is not a long bearing reinforced concrete wall. - Ceiling of the room above the insert (brick veneer

replacement): if the open space or the coating above the insert reach the room ceiling, it is necessary to protect the ceiling when it is made of

combustible material or it serves as a carrying element. The protection consists of a 6 cm (better is 10 cm) thick thermal insulation layer

(insulation material index: 12.07.21.75.11 according to AGI Q 132). It is recommended to take this preventive measure as a base intermediate

floor (e.g. made of sheet-metal) with the insulation material situated above it. If there is a gap between the ceiling and the insulation, there

must be diagonal venting for the gap (2x grilles min 50cm2.

 These preventive requirements have been set:

Brick veneer

Back wall

100 mm

Side wall

100 mm

Brick veneer replacement, insulation acc. to AGI

Q 132

Ceiling in the surround

60 mm

Thermal insulation layer

floor

30 /30 mm*

Side wall adjacent to the wall

120 mm

Back wall

120 mm

Side wall non contiguous to the wall

40 mm

Convection air ceiling

100 mm

Min. distances of the fireplace insert from the

inner side of the insulation

Back wall

150 mm

Side wall

40 mm

Distance of the bottom of the hearth from

the floor

100 mm

Distance of the top part of the fireplace

from the ceiling

500mm

**floor 30 mm, + 30 mm of insulation under the fireplace insert /mind the air inlet/

Thermal insulation: convection coating and convection access plate (outer contour of the facility) need to be coated from all sides by the

thermal insulation layer. The thermal insulation must be without joints and must overlap each other on the sides. If these insulating boards are

not fixed on walls, on coating or on abutting boards, it is necessary to fix them about 30 cm apart. The coating inwards the room (aperture)

does not need to be insulated when the insert is designed in such a way that the coating surface and the surface on the wood storing chamber

could reach a maximum temperature of 85 ºC. For surfaces made of mineral construction material, except for the areas where objects could be

detached, the maximum temperature is 120 ºC. Thermal insulation layers made of rock wool or comparable material must be thoroughly

coated from the room side and convection air area as a protection against fibre fraying.

If the connecting piece is passing through building elements of combustible materials (for example protecting walls), it is necessary to take

measurements in accordance with national technical standards and regulations acc. To ČSN 06 1008.

Permitted thermal insulation materiál and materiál for brick veneers (minimal requirements)

 Thermal insulation: cellular calcium-silicate slabs ρ = 250kg/m3, mineral wool boards, ceramics fibre boards.

 Brick veneer and surround: Liapor, bricks, concrete, no-fines concrete, stone.

 Alternate brick veneers and thermal insulation material: must be authorized. They must also fulfil every requirement for thermal

insulation and surrounds. Further information about these construction materials can be obtained in specialized stores.

Fireplace insert connection:

After insulation the fireplace insert can be connected by the connecting piece to the chimney. The fireplace insert is connected with the help of

the smoke flue made of sheet metal with the max. length of 1.5 m. the smoke flue must be provided with the safety pin to protect it against

sliding. When the connecting piece goes through parts with combustion materials (e.g. protective walls), it is necessary to keep instructions in

compliance with national technical standards and regulations according to ČSN 06 1008.

It is not allowed to put any other attachment which is not approvedby the manufacturer into the chimney connestion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeF Home Passive - HOT AIR FIREPLACE INSERTS Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info