Bedienungsanleitung BeF Home Passive - HOT AIR FIREPLACE INSERTS (Seite 8 von 9) (Englisch)

810623

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

________________________________________________________________________________________________________________________________

Firma: BeF Home, s.r.o. Strana 8 (celkem 9) Platí od: 1. 4. 2014

Vydání: 4

Convection air:

To prevent heat accumulation, the incoming and outgoing grates of convection air must be open when using the fire. To prevent heat

accumulation in heat distributing system, length of horizontal distribution piping must not be longer than 2,5m. The piping must always lead up.

Exit can´t lead vertically down.

Fire protection above a heat radiation area:

A minimum distance of 5 cm from the outer space of the insert coating to non-combustible building panels must be retained (e.g. shelves)

Fire protection in a heat radiation area:

A minimum distance of 80 cm forwards and sideways must be retained in front of the firebox hole - (furniture, carpets,

plants etc.)

Protection against injuries:

Do not forget that heaters have hot surfaces. Use the enclosed protective glove when working with the fire. You could be in a heat radiation area

(80 cm) only during mending, and if there is further contact, the skin can be burnt. Keep the fireplace out of the reach of children.

Application and activation:

Permissible fuel and economic,emission-reducing operation:

The fireplace insert is designed to use wood as fuel. The water content is max. 20% of dry weight. Logs should be stored in a dry and well

ventilated place for two years. Using wet logs leads to smoke with a tar condensation which could damage the chimney. In any case there is

excessive environmental pollution. Logs should be 30 cm. Wood is a very gaseous fuel and needs a lot of secondary air. Regulation with the

help of slow or permanent burning is not possible with this kind of fuel. Heating output during wood burning is determined by the amount of the

fuel used. The most ecological and economical is dry wood burning because the heating quality of fresh wood is lower than that of dry wood. As

for burning waste, it must be stressed that burning material such as plastic material, cardboard, painted wood, etc. are harmful for your fireplace

insert and furthermore is prohibited by the Emission Act. It is allowed to use firelighters, paper and small wood for lighting a fire only.

Do not use combustible liquid e.g. petrol, alcohol for lighting a fire and do not store similar kinds of liquid near your

fireplace insert!

The first lighting:

The fireplace insert should start with a small fire at first, so as not to harm it by very fast temperature rise. Smoke and the smell of burning which

may appear during the first lighting of a fire is a result of coating thermal curing. The room should be well aired during first heating.

Before the first use, check if all removable parts of the fireplace (block, deflector, grate and ash hole) are in the

right position – in accordance with the Equipment Certificate.

Instructions for burning hot air inserts and stoves with an automatic monitoring of the combustion process.

- Read carefully the manual of automatic monitoring system of the combustion process.

- Set up the temperature of combustion and timing to start burning.

- Please use recommended firestarters only. Do not use liquidy firestarters or solid spirits ones either. Recommendable firestarter is coils

of wood wool with paraffin.

- Procedure of burning: put firestarter down on the hot tip. Make sure that the firestarter has provided enough air around. Surround

firestarter by a proper amount of wood (according to technical list of the fireplace insert).

- Burn out all wood until automatic monitoring system indicates to load more wood again.

- Make sure to always load up your fireplace by a proper amount of wood only. You can find more information in the technical data

document. This way you help to avoid overhating your fireplace.

- By following these inctructions you can use your fireplace as frequently as you need.

- Before next burning keep in mind that the firelace insert needs to be completaly cooled down. The display of automatic monitoring

system recognizes and indicates it and will show you right timing.

- The door of fireplace must be closed while burning. Otherwise the automatic monitoring system can not work propely which could

cause an overheated fireplace.

- Do not overload your fireplace by abundance of wood. Overloading of fireplace could cause an improper burning, dirty glass and even

damaged fireplace.

- The Optimum amount of fuel is recommended in the Equipment Certificate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeF Home Passive - HOT AIR FIREPLACE INSERTS Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info