Bedienungsanleitung Behringer Ultralink UL2000M (Seite 17 von 24) (Englisch)

656672

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ULTRALINK UL2000M

 If the receiver is not powered on, no status is indicated. Briefly pressing the POWER button

will neither turn the transmitter on nor off!

3.3.2 Transmission frequency

1. Turn the selection switch to 9. The position of the MUTE switch is irrelevant.

2. Briefly press the POWER button.

3. Just like during programming, 6 blink medium-tempo codes indicate the individual digits that make up

the transmission frequency. Individual codes are separated from one another by brief pauses.

 The value 0 is signaled by a very short blink of the LED, and you will easily tell a

0 from a 1.

 If the receiver is not powered on, no status is indicated. Briefly pressing the POWER button

will neither turn the transmitter on nor off!

3.3.3 Preset

1. Make sure that the microphone is not set to mute (MUTE switch is set to OFF).

2. Turn the selection switch to 1, 2, 3 or 4 and confirm your selection by briefly pressing the POWER

button.

3. The LED indicates the preset number with the corresponding number of medium-tempo blinks.

3.3.4 Mic Gain

1. Make sure that the microphone is not set to mute (MUTE switch is set to OFF).

2. Turn the selection switch to 5 or 6 and confirm your selection by briefly pressing the POWER button.

3. The LED indicates the Mic Gain status with the corresponding number of medium-tempo blinks:

 Low Gain: The LED blinks once with medium tempo.

 High Gain: The LED blinks twice with medium tempo.

3.3.5 Auto Mute

1. Make sure that the microphone is not set to mute (MUTE switch is set to OFF).

2. Turn the selection switch to 7 or 8 and confirm your selection by briefly pressing the POWER button.

3. The LED indicates the Auto Mute status with the corresponding number of medium-tempo blinks::

 Auto Mute turned off: The LED blinks once with middle tempo.

 Auto Mute turned on: The LED blinks twice with middle tempo.

3.5 ULM2000 level setting

 To optimally set the level on your ULM2000, the High Gain or Low Gain setting has to be set

to the level of the signal being transmitted (ch. 3.2.5).

Adjust the gain control in the microphone channel of your mixing console so that the peak LED lights up only

occasionally or never at all. The EQ controls in the microphone channel should be set to mid-travel position

to start with. To get the sound you want, try changing the mic position relative to the sound source or even

move the microphone around in the recording room of your studio. Adjusting the angle at which walls face the

sound source can also be helpful. Only when the desired basic sound has been achieved should you start to

use equalizers and signal processors, if any at all (remember: less is often more!)

3. ULM2000 MICROPHONE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Ultralink UL2000M Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Ultralink UL2000M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info