Bedienungsanleitung Behringer Ultralink UL2000M (Seite 15 von 24) (Englisch)

656672

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ULTRALINK UL2000M

 If no entry is made for more than 5 seconds (either on the selection switch or by pressing

the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.

6. After a second brief blink break, an additional blink code is given as a confirmation:

 Successful loading of a preset is signaled with two slow blinks. The unit leaves the programming

mode.

 If the preset could not be loaded, the LED blinks quickly 5 times. In this case, start anew with

step 2.

7. After setting the desired preset, disengage the MUTE switch.

3.2.5 Mic Gain

You have the option to adjust the ULM2000 to the level of the signal being transmitted. If you talk very

softly into the microphone, we recommend the “High Gain” setting; if the sound is loud, select “Low

Gain.” This way, optimal transmitter drive is achieved.

1. Engage MUTE. The transmitter can now be switched into the programming mode.

2. Turn the selection switch to 0 and confirm your selection by keeping the POWER button pressed for 2

seconds. As a confirmation, the LED blinks slowly once and then once again with medium tempo. The

transmitter is now in the programming mode and waits for you to enter a one-digit number.

3. Select one of the following two digits on the selection switch:

 Low Gain: select 5

 High Gain: select 6

If a valid selection is made, the LED blinks quickly once to confirm your selection. This way, you can be

sure that a correct value is entered (in regard to preset, MicGain and Auto Mute selection) even before

confirming your selection.

 Selecting the values 1 thru 4 changes the preset settings (ch. 3.2.4). Selecting 7 or 8 changes

the Auto Mute settings (ch. 3.2.6). Values 9 and 0 are invalid.

4. Confirm your selection by briefly pressing the POWER button.

5. If the selection you made is valid, the LED blinks quickly once again. An invalid selection is indicated

with 5 quick blinks, and the unit is immediately no longer in the programming mode. In this case, start

anew with step 2.

After a brief break, a second blink code is given: The LED blinks according to the value selected (for

example, in this case 3 times) with medium tempo.

 Low Gain: the LED blinks once with medium tempo.

 High Gain: the LED blinks twice with medium tempo.

 If no entry is made for more than 5 seconds (either on the selection switch or by pressing the

POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.

6. After a second brief blink break, an additional blink code is given as a confirmation:

 Successful loading of a preset is signaled with two slow blinks. The transmitter leaves the

programming mode.

 If the setting for Mic Gain could not be stored, the LED blinks quickly 5 times. In this case, start

anew with step 2.

7. Disengage MUTE.

3.2.6 Auto Mute

If the transmitter is turned on, off or switched to another channel without first muting the receiver, or if the

transmission fails due to weak batteries, audible noise will result. Even if the squelch circuit is turned on at

the receiver end, it still requires some time to react, and such noise can not be suppressed safely.

To bridge this latency time, the ULM2000 offers a practical Auto Mute function:

 When the ULM2000 is being turned off, when you are switching channels or during low-battery indication,

an inaudible send signal is being transmitted.

 The ULR2000 recognizes this signal and automatically mutes the output before the transmitter is

actually turned off, switched to another channel or before it powers down on its own due to

battery charge being too low.

3. ULM2000 MICROPHONE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Ultralink UL2000M Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Ultralink UL2000M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info