Bedienungsanleitung Behringer X32 Producer (Seite 40 von 74) (Englisch)

660493

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

40 X32 PRODUCER DIGITAL MIXER User Manual

7.1.3 Navigation Methods

Following is an overview of how to navigate to the dierent console screens,

screen tabs, and sets of encoder parameters.

1. Press any of the assorted “View” buttons on any section of the console

top panel to switch the screen to the content that is tied to those

hardwarecontrols.

2. Alternatively, press any of the 10 hardware buttons located to the right-hand

side of the screen to switch the screen to eight other areas that are not

covered by the assorted “View” buttons.

3. On any given screen, press the Page Select left/right keys to navigate among

the various screen “tabs” within a screen category.

4. On any given screen, press the Layer up/down keys to navigate among the

various sets of encoder parameters located at the bottom of each screen.

Dedicated Screens

The 10 screens described in the following section are all “dedicated” screens.

They are accessed by pressing one of the 10 dedicated buttons located to the

right of the screen itself. This is in contrast to the “View” based screens, whichare

navigated to by pressing the “View” button in various sections of the console

toppanel.

Rotary Encoder Elements:

Gain

+0.00

Link

Lo Cut

Input

Select

Source

PRE

Insert

Ins Pos

InsF

Connect

Insert

0.3

Delay

The bottom of most screens contain 6 slots of information that are always paired

with the 6 hardware rotary encoders located directly underneath each slot.

Thehardware encoders are used to adjust parameters displayed in these slots,

and operate in the following manner:

1. Parameters displayed in the top half of each slot are most often “continuous”

type parameters, and are adjusted by rotating the corresponding encoder

located directly below the bottom of the screen.

• For example, in the “home” tab of the Home screen, the “gain”

parameter of the selected input (located in slot 1) is adjusted with the

rst encoder.

2. Parameters displayed in the bottom half of each slot (outlined in dark grey)

are most often “on/o” style parameters, and are adjusted by pushing the

encoder inward, using it as a button.

• For example, in the “home” tab of the Home screen, the “link”

parameter of the selected input (located in slot 1) is adjusted with the

rst encoder’s push action.

3. If a given screen contains more parameters than ts into the 6 slots, thena

2nd set of slots is made available. Navigate to the next set of slots by

pressing the Layer down key, and the bottom-of-screen content will change

to display the next set of 12 parameters to be adjusted. Press the Layer up

key to return to the original set of 12 parameters.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer X32 Producer Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Producer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info