Bedienungsanleitung Behringer X32 Producer (Seite 47 von 74) (Englisch)

660493

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

47 X32 PRODUCER DIGITAL MIXER User Manual

7.4 .2 Routing Screen: Analog Out Tab

The routing screen’s analog out tab allows the user to patch the console’s various

internal signal paths to the 8 analog XLR outputs that are located on the console

rear panel.

The X32 console allows for many dierent kinds of output signal paths, and this

screen is where these output paths are assigned to an actual physical rear panel

output so that the signal path can be patched to their eventual destination

(suchas the front-of-house PA speakers or a powered stage monitor).

To assign the various output paths to the rear panel XLR outputs, perform the

following steps:

1. Adjust the 1st encoder to select which of the 8 rear panel analog outs you

wish to assign an output signal path to.

2. Adjust the 3rd encoder to select an output path “category”.

These categories include:

• O

• Main (LRC) Mix

• Mix Bus Outputs

• Matrix Outputs

• Direct Outs

• Monitor

3. Adjust the 4th encoder to select a specic output path, including:

• O

• Main L

• Main R

• Main C/M

• Any of the 16 Mix Outputs

• Any of the 6 matrix outputs

• Any of the 32 direct outputs

• Any of the 8 Auxiliary Outputs

• Any of the FX Direct Outputs

• Monitor L

• Monitor R

• Talkback

4. Tap the 4th encoder to assign the selected output path,

completing the process.

5. Adjust the 5th encoder to select the signal tap point for the output

assignment. This determines where in the audio signal path the source is

“tapped” as it is sent to the physical rear panel output. The available signal

tap points include:

• Input

• Pre-EQ

• Pre-Fader

• Post-Fader

6. Tap the 5th encoder to assign the selected signal tap point.

7. Adjust the 6th encoder to adjust the amount of digital line delay applied to

the output path as it is sent to the rear-panel physical output. As the amount

of delay is adjusted, the current delay time is displayed in three dierent

units of measurement: Feet, Meters, and Milliseconds.

8. Tap the 6th encoder to toggle delay on/o. The “delay” label illuminates

when the delay is inserted into the signal path.

TIP: Applying a delay to an output signal is typically done when the console

is used in a “multi-zone” P.A. speaker setup, where some PA speakers are

located near the stage and a second set of speakers are located further back

within the audience. By applying an appropriate amount of delay only to

the speakers located near the stage, the audience hears the audio from the

closer/further speakers at the same time, insuring maximum time-alignment

and sound quality. The console assumes an operating temperature of 20°C/68°F

whencalculating the delay times.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer X32 Producer Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Producer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info