Bedienungsanleitung Behringer X32 Producer (Seite 49 von 74) (Englisch)

660493

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

49 X32 PRODUCER DIGITAL MIXER User Manual

7.4.4 Routing Screen: P16 Tab

The routing screen’s P16 tab allows the user to route various console signal paths

to the rear panel P16 Ultranet output. The Ultranet output allows for 16 channels

of audio to be sent, in digital form, to various accessories such as a personal

monitoring distribution box.

Using the P16 routing screen, the user can congure the P16 output to carry not

only the main LR mix, but also various audio “stems” of program material sources

from a bus send mix, such as a stereo drum mix, stereo keyboards, guitars,

bass, vocals, etc. Musicians on stage would then be free to each craft their own

personal mix of these musical stems, all delivered from the FOH position to stage

over a single Ethernet cable.

To select which audio signals are sent to the P16 bus, perform the followingsteps:

1. Adjust the 1st encoder to select which of the 16 channels in the P16 bus you

wish to select an audio source for.

2. Adjust the 3rd encoder to select a category of audio source to send to the

currently selected P16 channel. These categories include:

• Insert

• Main (LRC)

• Mix Bus

• Matrix

• Direct Out

• Monitor

3. Adjust the 4th encoder to select which specic signal path to feed to the

currently selected P16 output. Choices include:

• O

• Main L

• Main R

• Main C/M

• Any of the 16 Mix Outputs

• Any of the 6 matrix outputs

• Any of the 32 direct outputs

• Any of the 8 Auxiliary Outputs

• Any of the FX Direct Outputs

• Monitor L

• Monitor R

• Talkback

4. Tap the 4th encoder to assign the selected output path,

completing the process.

5. Adjust the 5th encoder to select the signal tap point for the output assignment.

This determines where in the audio signal path the source is “tapped” as it is

sent to the P16 output. The available signal tap pointsinclude:

• Input

• Pre-EQ

• Pre-Fader

• Post-Fader

6. Tap the 5th encoder to complete the signal tap point assignment.

7.4 .5 Routing Screen: Card Output Tab:

The routing screen’s card tab allows the user to patch various signal paths to the

physical inputs and outputs of the X-USB card. The X-USB’s signal path provides

32channels of inputs and 32 channels of outputs. The 32 card inputs can be used

as alternate sources for the two input fader layers, switchable in banks of 8.

To assign an output path to the option card, perform the following steps:

1. Adjust the 1st encoder to select which 8-channel output path to send to the

rst 8 outputs of the card. Choices include:

• Local 1-8

• Local 9-16

• AES50-A 1-8

• AES50-A 9-16

• AES50-A 17-24

• AES50-A 25-32

• AES50-A 33-40

• AES50-A 41-48

• AES50-B 1-8

• AES50-B 9-16

• AES50-B 17-24

• AES50-B 25-32

• AES50-B 33-40

• AES50-B 41-48

• Card 1-8

• Card 9-16

• Card 17-24

• Card 25-32

• Out 1-8

• Out 9-16

• P16 1-8

• P16 9-16

• Aux 1-6/Mon

2. Tap the 1st encoder to assign the selected output path,

completing the process.

3. Repeat the process with encoders 2-4 to select output paths for the other

24channels of card outputs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer X32 Producer Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Producer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info