Bedienungsanleitung Behringer X32 Rack (Seite 20 von 64) (Englisch)

660494

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

20 X32 RACK DIGITAL MIXER User Manual

5.4 How do I add one of the 8 internal eects

to the sound?

There are two types of eects that are commonly used:

• “Eects Loop” (side chain) style eects, where multiple channels all send

varying amounts of their signal to a common eect, such as a reverb,

delay,or chorus.

• “Insert” style eects that are inserted in to the signal path of a single

channel of audio. Examples would be a graphic EQ, lter, exciter,

ortubeemulator.

To apply an “Eects Loop” style eect:

• Press the “Eects” menu button. The main screen will show the FX

home screen where dierent eects processors are assigned to the 8

processing slots.

• Adjust rotary encoder #6 to highlight the rst eects processor; it will be

surrounded by an orange outline.

• Adjust rotary encoder #1 and rotary encoder #2, selecting your desired bus as

the source for both the left and right inputs of the rst eect processor.

• Adjust rotary encoder #5 to select a specic eect processor,

suchas “Ambience”.

• Rotate the Channel Select knob until 1 L appears in the channel number

display and press the knob. Use the Channel Level knob to bring the return

up to 0 dB. Turn the Channel Select knob to the right one click so that 1r

appears in the display, the press the knob. Bring the return level up to 0 dB.

• Back on the Eects page, press the PAGE SELECT right button to switch the

screen to the editor for the Ambience processor. The screen will switch to an

editor page for the rst processor. Adjust the rotary encoders to tailor the

eect to your liking.

• Press the Home button again and tab over to the ‘sends’ page. Raise

the virtual faders for the channels to which you want to add the eect.

The higher you raise the fader, the more of that channel's signal will be sent

to the processor.

To apply an “insert” style eect:

• Press the “Eects” menu button.

• As the eects on the left side are also able to handle complex send eects

like reverb, the slots on the right side shall be used for insert eects like

limiter, graphic EQ, etc. You can also use insert eects on the left side,

butthis will limit your use of reverbs and other processor-intensive eects.

• Adjust rotary encoder #6 to highlight one of the eects processors on the

right side; it will be surrounded by an orange outline.

• Adjust rotary encoder #1 and rotary encoder #2, selecting “Insert” as the

source for both the left and right inputs of the eect processor.

• Adjust rotary encoder #5 to select a specic eect processor, such as

“precision limiter”.

• Select the specic input or output channel you wish to use the inserted

eect on.

• Press the HOME button, then the PAGE SELECT right button to navigate to the

selected channel’s “Cong” screen.

• Adjust rotary control #6 to select the specic processor you have applied the

eect to, in this case “Ins FX 5L”. Press the encoder to connect the selected

insert eect.

• The Precision Limiter is now applied as an insert on the selected channel.

Sending more than one channel through the same insert eect is, of course,

prohibited. There will be a warning when you try to insert an eect slot that

has already been used as an insert on any other channel. Both sides of a dual

type eect can be used as inserts on dierent channels or buses.

5.5 How do I use an outboard

eectsprocessor?

In some situations, you may wish to use a loop-style eect provided by an

external eect processor, as opposed to using one of the eight built-in processors.

To do so:

• Press the ROUTE button, page right to the “Aux Out” screen, and adjust the

rst and fourth encoders to tie a rear panel ¼" aux out, such as Aux Out 1,

toan available mix bus, such as Mix Bus 2.

• Patch rear panel Aux Output 1 to the input of your external eects processor.

• Patch the output of the external eects processor to rear panel Aux Input 1.

• Rotate the Channel Select knob until A1 appears in the display, the press the

knob. On the Home screen, ‘home’ tab, verify that the Main LR is highlighted.

• Move the Aux 1 channel level to 0 dB.

• Adjust the settings on the external eects processor to taste.

5.6 How do I set up live stage monitoring?

Setting up a live stage monitor mix using conventional monitors:

1. Press the ROUTE button and page right to the Analog Out page.

2. Adjust the rst encoder to select a rear panel analog output (e.g. Output 1),

then adjust the fourth encoder to select a mix bus (e.g. Mix Bus 1). Whenthe

source and destination have been selected, press the 4th encoder to

complete the assignment.

3. Adjust the 5th encoder to set up the monitor send as pre-fader, or pre/post

EQ. This will prevent the monitor mix from changing when the front-of-

house mix is adjusted.

4. Connect a cable from rear panel analog Out 1 to the input of:

a) A powered stage monitor

b) An external amplier feeding a passive stage monitor

c) A transmitter for a set of wireless in-ear monitors

5. Rotate the Channel Select knob to select Bus 1, then press the knob.

Adjust the Channel Level knob to 0 dB. You can change the output on this

bus later.

6. To adjust the mix sent to the monitor, select an input channel with the

Channel Select knob, nagivate to the Home screen’s ‘sends’ tab, then raise

the faders for each bus that the channel should be sent to.

Behringer X32 Rack Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer X32 Rack

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info