Bedienungsanleitung Behringer XAir - XR12 (Seite 18 von 46) (Englisch)

660502

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

18 X AIR User Manual

5. Adjust the Ratio to determine how aggressively the dynamics are aected.

6. The Wet/Dry ratio determines how much of the signal is left unaected by

the processor.

7. Use the Gain fader to compensate for changes in level caused by

theprocessor.

8. Engage the Key Filter with the on/o button.

9. Select between an aggressive Linear or smooth Logarithmic operation,

andbetween Peak or RMS input response. RMS is most common in

compressors, and responds to the average level of incoming audio,

whereasthe Peak setting responds to brief spikes in loudness that would

beallowed through when set to RMS.

10. Access the Key Filter parameters by pressing this button.

11. Adjust the Attack knob to set how quickly the compressor takes eect when

the input signal rises above the threshold.

12. Adjust the Hold knob to set how long the compressor takes to enter the

release cycle once the audio drops below the threshold.

13. Adjust the Release knob to set how quickly the compressor releases after the

audio drops below the threshold.

14. Select a high-pass, low-pass or mid peak frequency and slope for the key

lter. The specic frequency can be selected by dragging the line across the

frequency chart.

15. Select a source for the key lter.

5.6 Channel EQ

1. Select the type of EQ for each of the 4 bands. Typically cut or shelf EQs are

used for the highs and lows, whereas PEQ (parametric) and VEQ (vintage)

areused for the mid range adjustments.

2. Use the Gain knob to adjust the desired boost or cut to the

selectedfrequency.

3. Adjust the Width (Q) to determine how wide or narrow the frequency

adjustment will be.

4. Use the Freq(uency) knob to select the center frequency for PEQ and VEQ

types, and the starting frequency for cut or shelf EQs.

5. Engage the EQ with the on/o button.

6. Press this button to open the preset list where your settings can be saved

can recalled.

7. Press one of the band buttons to select the band. Drag the button left/right

to set the frequency, and up/down to set the boost or cut. The desired band

must be selected before adjusting the width parameter.

8. Engage the RTA (real time analyzer) with this button. The RTA is pre-EQ by

default, but can be adjusted on the Setup - Audio/MIDI page.

9. Press this button to reset the currently-selected band.

5.7 Insert

Press the folder icon to engage the insert eect. Scroll through the list of eects

blocks to select the desired routing.

5.8 Presets

The Presets tab allows channel presets to be recalled, edited and saved.

Pressthepage icon on the right to save a new preset. Press the pencil icon to

edit or delete a preset, and press on one of the saved presets to save changes

orloadthatpreset.

5.9 Output

The panorama can be adjusted to position the channel in the stereo eld.

5.10 Meters

The Meters page is accessed via the icon at the top of the main screen. This page

allows easy monitoring of all analog and digital levels, including USB channels,

Gate and Dynamics activity, P-16 channels and the Main and Solo buses.

5.11 Shows

The Shows page allows performances to be saved for various venues,

artists,setsand arrangements for later recall. Within those shows,

individualsnapshots can be saved, edited and recalled. Press the page icon

tosave a new show or snapshot. Press the pencil icon to edit or delete a saved

showor snapshot. Pressing on a show or snapshot will allow any changes to

besaved, orfor a new snapshot to be loaded.

(1)

(2)

(3)

(6)

(5)

(7) (4) (8) (9)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer XAir - XR12 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer XAir - XR12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info