Bedienungsanleitung Behringer XAir - XR12 (Seite 28 von 46) (Englisch)

660502

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

28 X AIR User Manual

adjusted. If applicable, a tap tempo button is available to manually enter the rate

of delays or choruses. The button will ash to indicate the tempo. Click the Insert

button to engage the eect as an insert instead of side-chain. Select the channel

or bus assigned to the eect with the pull-down menu. See the Eects Overview

chapter for more details.

7.10 Meter Tab

The Meter tab allows easy monitoring of all analog and digital levels,

including USB channels, Buses, Ultranet outputs, and the Main and Solo buses.

7.11 Setup Menu

The Setup menu allows the wireless connection to be congured and allows

various global parameters to be selected and adjusted.

Connect Tab

After you connect your computer to the internal Access Point or external router,

the software will likely automatically recognize the mixer and ask to connect.

Once connected, a prompt will ask if you would like to transfer settings from the

mixer to PC, or from the PC to the mixer. Click ‘cancel’ if you don’t want to sync

settings. The Connection tab also allows you to manually assign an IP address.

If you have rmware 1.09 or later, you can update the rmware directly from this

screen as well.

Note - save your settings to your computer’s hard drive before updating

the rmware!

By default, a generic name, such as XR18-1B-10-F3, will be assigned to your

mixer. This can be changed to something more specic and recognizable.

The console can also be initialized back to its factory state, but be aware that all

settings will be erased. We highly recommend using the Save function to store

any important scenes to your computer's hard drive.

Access Point, WLAN, LAN Tabs

The Access Point, WLAN and LAN tabs allow the wireless connection to be

congured. See the 'Network Connection' chapter for details.

Audio/MIDI Tab

The Audio/MIDI tab allows various global settings to be assigned. The console

can operate at 48 kHz or 44.1 kHz. Mute the main LR fader before changing clock

rates as pops can occur.

Engage the Safe Levels function to automatically mute the outputs during a

power cycle. This is particularly useful for situations where the mixer is always

connected to a PA system or monitoring setup.

The Link Preferences allow specic preamp elements to be synchronized when

adjacent channels are linked.

The console defaults to “soft mutes”, meaning that if a channel has been

specically muted, and is also a part of a mute group, when the mute group

is unmuted, the channel that was specically muted will also be unmuted.

Selecting Hard Mutes will cause a channel that has been muted with its

dedicated Mute button will remain muted even if a mute group to which it

belongs is unmuted. DCA Groups normally just control volume levels without

actually having audio routing through them. However, engaging DCA Groups in

the Mute System will enable channels to be muted via DCA group assignments.

The X18/XR18 has an 18x18 channel interface built-in, but sometimes

this is overkill for a recording session. For overdubs and simple tracking,

the 2x2 interface is more ecient and easier on processing power.

Various send (Tx) and receive (Rx) preferences are selectable for the

MIDI conguration.

Monitor Tab

The monitor source defaults to the main LR (post-fader), but you can select a

bus, aux, USB 17/18 or a combination of buses. Soloed channels and buses can be

monitored pre or post-fader. PFL attenuation can be engaged and the relative

levels for monitor and source can be set. Click the DIM button to enable dimming

and select the attenuation level. The monitor bus can be set to mono and can be

muted from this page.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer XAir - XR12 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer XAir - XR12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info