Bedienungsanleitung Behringer Xenyx X2442USB (Seite 13 von 19) (Englisch)

660523

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

13 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual

FBQ FEEDBACK DETECTION

The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the

frequency band faders to indicate the critical frequencies. On a per-need basis,

lower the frequency range in question somewhat in order to avoid feedback.

Thegraphic stereo equalizer has to be turned on in order to use this function.

◊ Logically, at least one (ideally several) microphone channels have to be

open for feedback to occur at all!

Feedback is particularly common when stage monitors (“wedges”) are

concerned, because monitors project sound in the direction of microphones.

Therefore, you can also use the FBQ Feedback Detection for monitors by placing

the equalizer in the monitor bus (see MAIN MIX/MONITOR).

4. Digital Eects Processor

24-BIT MULTI-EFFECTS PROCESSOR

Here you can nd a list of all presets stored in the multi-eects processor.

Thisbuilt-in eects module produces high-grade standard eects such as reverb,

chorus, anger, delay and various combination eects. Use the Aux Send FX on

the channels and the Aux Send FX master control to determine the input signal of

the eects processor.

X1832USB

Fig. 4.1: Digital eects module

The built-in stereo eects processor has the advantage that it does not need to

be wired up. This excludes the danger of humming or level mismatch right from

the start and thus considerably facilitates use.

These eect presets are classical “mixing eects”. If you move the STEREO AUX

RETURN FX control, you mix the channel signal (dry) and the eect signal. Youcan

control the balance between the two signals with the channel fader and the

STEREO AUX RETURN FX control.

FX OUT

Mixing consoles X2222USB and X2442USB have a separate output for the eects

device, which is unbalanced and stereo (tip = left signal; ring = right signal;

sleeve = ground/shielding). Thus, you can record, for example, a vocal track

enhanced with reverb in parallel to a “dry” vocal track; when doing the mix-down

later on, you can freely determine the amount of reverb added.

◊ The X2442USB has the effect output on the rear, X2222USB has it

located next to the aux sends on the front panel.

FX FOOTSW.

Connect a standard foot switch to the foot switch jack and use this to switch

the eects processor on and o. A light at the bottom of the display indicates

wheater the eects processor has been muted by the foot switch.

◊ In Chapter 6.2 you will find an illustration showing how to connect your

foot switch correctly.

LEVEL

The LED level meter on the eects module should display a suciently high

level. Take care to ensure that the clip LED only lights up at peak levels. If it is

lit constantly, you are overloading the eects processor and this could cause

unpleasant distortion.

PROGRAM

You can select the eect preset by turning the PROGRAM control. The display

ashes with the number of the current preset. To recall the selected preset,

presson the button; the ashing stops. You can also recall the selected preset

with the foot switch.

5. Rear Panel Connectors

5.1 Main mix outputs, insert points and control

room outputs

X2442USB

Fig. 5.1: Main Mix outputs, main mix insert points and control room outputs

MAIN OUTPUTS

The MAIN outputs carry the MAIN MIX signal and are on balanced XLR jacks with

a nominal level of +4 dBu. In parallel with this, ¼" phone jacks carry the main

mix signal in a balanced format (X1622USB: here, the phone jack outputs are

unbalanced and located on the front panel).

CONTROL ROOM OUTPUTS (CTRL OUT)

The control room output is normally connected to the monitoring system in the

control room and carries the stereo mix or, when selected, the solo signals.

MAIN INS(ERTS) (X2442USB only)

These are the insert points for the main mix. In the signal path, they are

post-main mix amp, but pre-main fader(s). Use them to insert, for example,

adynamics processor or graphic equalizer. Please also note the information on

insert points in chapter 5.3.

5.2 Subgroup outputs

Fig. 5.2: Subgroup outputs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx X2442USB Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx X2442USB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info