Bedienungsanleitung Behringer Xenyx X2442USB (Seite 14 von 19) (Englisch)

660523

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

14 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual

SUB OUTPUTS

The subgroup outputs are unbalanced and provide the mix of those channels

assigned to each subgroup with the SUB switch (X2442USB: switches 1-2 or 3-4)

next to the channel faders. Thus, you can, for example, route a subgroup to a

second console or use the output as a recording output in parallel to the main

outputs. In this way, you can record several tracks simultaneously. With an

8-track recorder, use Y cables and wire the inputs of your machine so that you

have 2 x 4 tracks available (e.g. channel 1 to track 1 and 2, etc.). In the rst pass,

you can record the tracks 1, 3, 5 and 7, in the second the tracks 2, 4, 6 and 8.

The XENYX 2442FX already has subgroup outputs wired in parallel (1-5, 2-6, etc.).

5.3 Inserts

X1622USB

Fig. 5.3: Insert points

◊ On the 2442FX the channel insert points are located on the control

panel between the line input and the GAIN control.

Insert points are very useful to process channel signals with dynamic processors

or equalizers. Unlike reverb or other eects devices, whose signals are usually

added to the dry signal, dynamic processors are most eective on the complete

signal. In this case, aux send paths are a less-than-perfect solution. It is better

to interrupt the signal path and insert a dynamic processor and/or equalizer.

Afterprocessing, the signal is routed back to the console at precisely the same

point it left. However, the channel signal path is interrupted only if a plug is

inserted into the corresponding jack (stereo phone plug: tip = signal output;

ring= return input). All mono input channels are equipped with inserts. Theyare

pre-fader, pre-EQ and pre-aux send. Inserts can also be used as pre-EQ direct

outputs, without interrupting the signal path. To this end, you will need a cable

tted with mono phone plugs on the tape machine or eect device end, and a

bridged stereo phone plug on the console side (tip and ring connected).

5.4 Direct outputs (X2442USB only)

X2442USB

Fig. 5.4: Direct outputs

DIRECT OUTPUTS

The direct outputs of the X2442USB (1 each per mono input channel) are ideal for

recording if several tracks are to be recorded simultaneously. These unbalanced

phone jacks are post-EQ, post-mute and post-fader.

5.5 USB input/output

Fig. 5.5: USB input/output

The XENYX mixer line has built-in USB connectivity, allowing stereo signals to

be sent to and from the mixer and a computer. The audio sent from the mixer to

a computer is identical to the MAIN MIX. Audio being sent to the mixer from a

computer can be routed to the main mix with the 2-TR/USB TO MAIN button.

Connect the USB type B plug into the USB jack on the mixer, and the other end

into a free USB port on your computer. There are no required drivers, but we

recommend that PC users install the included ASIO driver. The driver can also be

downloaded from behringer.com.

5.6 Voltage supply, phantom power supply

and fuse

All Models

Fig. 5.6: Voltage supply and fuse

FUSE HOLDER/IEC MAINS RECEPTACLE

The console is connected to the mains via the cable supplied, which meets the

required safety standards. Blown fuses must only be replaced by fuses of the

same type and rating. The mains connection is made via a cable with IEC mains

connector. An appropriate mains cable is supplied with the equipment.

POWER switch

Use the POWER switch to turn on the mixing console. The POWER switch should

always be in the “O” position when you are about to connect your unit to

themains.

To disconnect the unit from the mains, pull out the main cord plug.

Wheninstalling the product, ensure that the plug is easily accessible. If mounting

in a rack, ensure that the mains can be easily disconnected by a plug pull or by an

all-pole disconnect switch on or near the rack.

◊ Attention: The POWER switch does not fully disconnect the unit from

the mains. Unplug the power cord completely when the unit is not used

for prolonged periods of time.

PHANTOM switch

The PHANTOM switch activates the phantom power (necessary to operate

condenser microphones) on the XLR sockets of the mono channels. The red +48V

LED illuminates when phantom power is on. As a rule, dynamic microphones can

still be used with phantom power, provided that they are wired in a balanced

conguration. In case of doubt, contact the microphone manufacturer!

◊ Connect microphones before you switch on the phantom power supply.

Please do not connect microphones to the mixer (or the stagebox/

wallbox) while the phantom power supply is switched on. In addition,

the monitor/PA loud-speakers should be muted before you activate the

phantom power supply. After switching on, wait approx. one minute to

allow for system stabilization.

◊ Caution! Please also note the information given in chapter 6.2.1

“Audio connections”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx X2442USB Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx X2442USB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info