Bedienungsanleitung Behringer Xenyx XL1600 (Seite 9 von 22) (Englisch)

660520

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

9 XENYX XL3200/XL2400/XL1600 User Manual

INSERT

The INS(ert) connector (¼" stereo jack connector) is used to connect to external

signal processors. Here you can hook up a compressor, noise gate or equalizer to

process the signal of a single channel. The insert jack is placed before the fader,

EQ and aux send. Please use an insert cable to connect to the insert point.

DIRECT OUT

This ¼" mono jack connector is a direct output which taps the signal after the

channel fader to route it to a multi-track recorder, for example. By modifying the

circuit board in the unit, the signal can also be tapped pre-fader (see chapter 6).

4.3 Stereo inputs

LINE L (MONO), LINE R

The stereo channels consist of two line inputs (¼" jacks), one for the left and

one for the right channel. The inputs are balanced (TRSconnectors), but it is also

possible to connect to unbalanced plugs (TS connectors). These channels can also

be used as mono channels by connecting to the jack labeled “L” (left).

MIC

The stereo channels also consist of XLR inputs for connecting to microphones

DIboxes and multicores.

+48 V

This is the phantom power for operating capacitor microphones along with the

control LED located next to the switch and in the Trim section of the stereo channels.

4.4 Main mix outputs

OUT A

The OUT A outputs are balanced XLR connectors with a nominal operating level of

+4 dBu and provide the main mixsignal.

OUT B

The OUT B outputs provide the MAIN B signal the volume level of which can

becontrolled.

INSERT

Like the channel inserts, the INS(ert) connectors can be usedto hook up a

dynamics processor or equalizer for further processing of the mix signal on OUT A.

4.5 Subgroup connectors

GROUP OUT 1 - 4

These four GROUP OUTS 1 – 4 carry the signals of the individual subgroups.

Formulti-tracking connect the outputs to the inputs of a multi-track recorder.

INSERT

Each subgroup has an insert jack which is labeled INS. Here you can connect to

a noise gate, compressor or equalizer to process the subgroup signal as a whole.

For example, route your background vocalists to one subgroup bus and then use

a compressor to bring the vocals closer together. This makes it sound more like a

choir rather than a group of individual soloists. The insert point is placed before

the group fader, allowing the dynamics processors (noise gate, compressor, etc.)

to be optimally used and not aected by changes in volume level of the group

fader. Please use an insert cable to connect to the insert point.

SPEAKERS

The SPEAKERS outputs provide the same signal as the headphone outputs.

Usethese outputs to hook up monitor speakers. This is helpful when the mixing

console is not located close the performance but in a separate room, such as a TV

control room. It is also possible to hook up a stage monitor, ideally one identical

to the monitors being used on stage, to listen in on the sound as perceived from

the stage monitors.

4.6 CD/tape connectors

The CD/TAPE input connectors are used to hook up CD players, tapedecks or other

line-level sources.

OUT

The CD/TAPE output connectors provide the stereo main mix signal to a tape deck

or DAT recorder to record your mix. The signal is taken pre-fader so that it will not

be inuenced by the fader positions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx XL1600 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx XL1600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info