Bedienungsanleitung Behringer Xenyx XL2400 (Seite 13 von 22) (Englisch)

660519

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

13 XENYX XL3200/XL2400/XL1600 User Manual

SOLO

Press the SOLO switch to hear the signal on your headphones and simultaneously

see it on the monitor display ½). The corresponding LED lights up when the solo

function is activated.

CLIP

The CLIP LED lights up as soon as the channel's level is too high. In this case, turnthe

TRIM control to reduce the channel's input amplication until the LED goes out.

SIG

The SIG LED lights up when a channel's signal is higher than -20 dB. The LED is

not aected by the fader. The signals are indicated even when the fader is pulled

down and the channel is muted.

Fader

The channel fader governs the level of the channel signal as part of the main

mix(or submix)

1-2, 3-4, MAIN

The routing switch feeds the signal to the respective subgroup or the main mix

or both. Please note that when using the routing switch to route a stereo signal

to the subgroups the balance control needs to be centered so that the signal is

routed to two groups and remains in stereo.

5.3 Main section

5.3.1 MAIN A section

BAL(ANCE)

The BAL(ANCE) control adjusts the mix of the left and right output signal before

both signals are routed to the MAIN A output. This way the left and right volume

level of the mixer sumcan individually be adjusted if necessary.

MAIN MUTE

When the MAIN MUTE switch is pressed, all input channels are muted. The MUTE

LED lights up when the MUTE switch is pressed. Only the CD/TAPE signal will be

routed to the main mix. In this way, you can prevent the microphones from picking

up unwanted sounds or noise that would interfere with CD playback during a break.

The main mix and channel faders can remain in their normal positions while playing

back music from CD (usingthe CD/TAPE inputs, so you don’t lose your mix.

MAIN A

Use this high-precision MAIN fader to control the output level of the main mix.

MAIN B

Depending on the settings of the MAIN B section, the level of the Main B output is

aected by the MAIN A fader.

5.4 Level meters

Four high-resolution LED meters indicate the levels of the monitor buses' and

mixer sum's output signals. As soon as you have pressed the solo switch on the

mixing console, the monitor LED meter automatically shows the solo signal.

Themaster signal is alwaysindicated.

1 MON 2

The monitor meters indicate the levels of the monitor buses 1 and 2. In solo mode

(SOLO LED lights up) thePFL signal (mono, only left meter) or the AFL signal

(stereo, left and right meter) are shown. Thisdepends on the state of the PFL and

AFL switch inthe solosection.

SOLO

When a SOLO switch is pressed on the mixing console, not only the corresponding

LED lights up, but also the global SOLO LED. This way you can keep a cool head

when mixing live and don't have to check the whole console to see that one

SOLOswitch is active. Simultaneously this LED indicates that the monitor meters

are in solo mode.

MAIN

The high-precision level meter accurately indicates the output signal

level(MAINOUT A).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx XL2400 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx XL2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info