Bedienungsanleitung Behringer Xenyx XL3200 (Seite 8 von 22) (Englisch)

660518

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

8 XENYX XL3200/XL2400/XL1600 User Manual

4. Connectors

Let's begin with the rear panel where the majority of inputs and outputs

arelocated.

4.1 Power supply

IEC receptacle

The mains connection is a standard IEC receptacle. Anappropriate power cord is

supplied with the unit.

FUSE HOLDER

Before connecting the unit to the mains, ensure that the voltage setting matches

your local voltage. Blown fuses should only be replaced by fuses of the same type

and rating. Please also read the information given in chapter “Specications.”

POWER

Use the POWER switch to turn on the mixing console. The POWER switch

should always be in the “O” position when you are about to connect your

unitto the mains.

To disconnect the unit from the mains, pull out the main cord plug.

Wheninstalling the product, ensure that the plug is easily accessible.

Ifmountingin a rack (XL1600 only), ensure that the mains can be easily

disconnected by a plug pull or by an all-pole disconnect switch on or near

therack.

◊ Please note: The POWER switch does not fully disconnect the unit from

the mains. To disconnect the unit from the mains, pull out the main

cord plug or appliance coupler. When installing the product, ensure the

plug or appliance coupler is readily operable. Unplug the power cord

when the unit is not used for prolonged periods of time.

SERIAL NUMBER

This is the serial number of the mixing console.

4.2 Mono inputs

MIC

The balanced XLR input connects to microphones, DIboxesand multicores.

(Multicores are cables that have multiple cores and which run from the so-called

stagebox to the mixer.)

◊ Connect the microphone and mute all mixer outputs before turning on

the phantom power to avoid noise when the microphone is turned on.

Please wait for about one minute when switching on the mic until the

voltage is stable. Only then turn on the input amplification.

◊ Caution! Never use unbalanced XLR connectors (pins 1 and

3 interconnected) on the MIC input jacks, if you want to use

phantom power.

+48 V

Phantom power is used for operating a capacitor microphone. A control

LED lights up next to the switch when the phantom power supply is active.

Additionalcontrol LEDs are located in each Trim section of the mixer's

channels. As a rule, dynamic microphones can still be used with phantom

power, providedthey are wired in a balanced conguration. In case of doubt,

contactthemicrophone manufacturer!

LINE

This is a ¼" jack connector which connects to line-level signal sources

(forexample, keyboards, CD players and wireless microphone receivers).

The input is balanced (TRS connector) but can also be used with unbalanced

connectors (TS connector).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx XL3200 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx XL3200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info