Bedienungsanleitung Behringer Xenyx XL3200 (Seite 10 von 22) (Englisch)

660518

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

10 XENYX XL3200/XL2400/XL1600 User Manual

4.7 FX/Mon/Aux sends

FX 1 and 2

The FX outputs 1 and 2 provide the signals of the eects buses 1 and 2.

Thesesignals may be sent to external eects processors and are routed back over

the AUX-RETURN inputs or separate input channels, for example.

MON 1 and 2

The monitor outputs 1 and 2 provide the signals of the monitor buses.

Thesesignals may be be sent to stage loudspeakers. To prevent interference due

to the long cables being used between stage and mixing console, the outputs

are balanced XLR connectors. What's more, youhave the right connectors when

working with multicores.

AUX 1 and 2

The AUX outputs 1 and 2 provide the signals of the AUX buses 1 and 2.

Youcanswitch these buses pre-fader and post-fader so that they may be

usedforeects as well as for monitor applications.

4.8 Aux returns

AUX RETURN

The stereo AUX inputs 1 und 2 let you connect the mixer to additional equipment

(players,eectsprocessors, submixers, etc.). Thesignal is sent to the signal sum.

FX RETURN

The stereo FX RETURN connectors 1 and 2 are linked to the outputs of external

eects processors. Depending on the routing, the signals are sent to the

subgroup or the main mix bus.

4.9 Light and headphone connectors

LAMPS

The LAMPS plugs are for connecting gooseneck lamps with BNC connectors.

Thepower supply is 12 V _ and the total connection load is 5 Watts a lamp.

PHONES

The PHONES outputs (¼" stereo jacks) let you plug in your headphones.

5. Control Elements

This chapter describes the various control elements of your mixing console.

Eachcontrol and switch is explained in full detail.

5.1 Mono channels

+48 V

This control LED lights up as long as the phantom power is switched on.

Theswitch is found on the rear panel of the unit.

Trim

The TRIM control adjusts the input gain.

◊ Be sure to set this control fully counter-clockwise before you connect or

disconnect a signal source to or from one of the inputs.

The dial oers 2 dierent value ranges. The rst value range between 0 and +60

refers to the microphone input, indicatingthe degree of amplication applied to

the input's signal. Thesecond value range between -20 and +40 dB refers to the

amplication of the line input. When centered (at12o'clock), the line signals are

neither boosted nor cut.

80 Hz

Press the 80 Hz switch to activate the high-pass lter which blends out

low-frequency noise (-3 dB at 80 Hz, 18 dB/octave).

Equalization

The mono input channels provide 4-band equalization with 2semi-parametric

mids. You can boost or cut the bands up to 15 dB. When in center position (0 dB),

the equalizer has a atresponse.

HIGH

The high-frequency range is processed with a shelving lter above 12 kHz.

HIGH MID

A semi-parametric peak lter processes the upper mid range between 400 Hz

and 8 kHz. The FRE control selects the frequency which is boosted or cut by using

the HIGH MID control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx XL3200 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx XL3200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info