Bedienungsanleitung Behringer Xenyx XL3200 (Seite 12 von 22) (Englisch)

660518

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

12 XENYX XL3200/XL2400/XL1600 User Manual

CLIP

The CLIP LED lights up as soon as the channel's level is too high. In this case,

reduce the channel's input amplication with the TRIM control.

SIG

The SIG LED lights up when a channel's signal is higher than -20 dB. The LED is

not aected by the fader. The signals are indicated even when the fader is pulled

down and the channel is muted.

Fader

The channel fader adjusts the level of the channel signal as part of the main mix

(or submix).

1-2, 3-4, MIX

The routing switch routes the signal to the respective subgroup or the main mix

or both. The XENYX features 4 subgroups. The PAN control determines the group

to which the signal is routed (fully left: Sub 1 or 3, fully right: Sub 2 or 4).

5.2 Stereo channels

+48 V

This control LED lights up when the phantom power is activated. The switch is

located on the rear panel of the unit.

MIC TRIM

The MIC TRIM control adjusts amplication of the microphone input.

Theamplication ranges between 0 and +60 dB.

◊ Be sure to set this control fully counter-clockwise before you connect or

disconnect a signal source to or from one of the inputs.

80 Hz

Press the 80 Hz switch to activate the high-pass lter which blends out

low-frequency noise (-3 dB at 80 Hz, 18 dB/octave).

LINE TRIM

The LINE TRIM control adjusts the amplication of the LINE input,

rangingbetween -20 and +20 dB. When centered (at 12 o'clock),

thelinesignalisneither boosted nor cut.

5.2.1 Equalizer stereo channels

The stereo channels provide 4-band equalization. Each frequency band can be

boosted and cut up to 15 dB and has a at response when the controls are in

center position.

HIGH

The HIGH control of the EQ section adjusts the high-frequency range of the

respective channel. This is a shelving lter which boosts and cuts the frequencies

above 12 kHz.

HIGH MID

The HIGH MID control adjusts the mid frequency range. Thisisapeak lter which

boosts and cuts the frequencies centered at3 kHz.

LOW MID

The LOW MID control adjusts the mid frequency range. Thisisapeak lter which

boosts and cuts the frequencies centered at 300Hz.

LOW

The LOW control adjusts the low-frequency range. This is a shelving lter which

boosts and cuts the frequencies below 80 Hz.

The EQ push-button switch activates the equalizer. Toggle the EQ to give you a

quick comparison between unprocessed and processed signal.

5.2.2 Stereo channel FX/MON/AUX send paths

The aux and FX paths of the stereo channels work in principle the same way as

the mono channels. Since the aux buses are mono, the stereo signal needs to be

converted to a mono signal before being routed to these buses.

5.2.3 Channel fader, pan control, mute switch, etc.

BAL(ANCE)

The BAL(ANCE) control has the same function as the PAN control on the mono

channels. It determines the relative volume of the left and right input signals

before they are routed to the stereo main mix bus (or to two subgroups).

MUTE

Use the MUTE switch to mute the channel signal. The MUTE LED is illuminated

when the channel is muted

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer Xenyx XL3200 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer Xenyx XL3200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info