Bedienungsanleitung BEKO CWB 9910 (Seite 8 von 44) (Englisch, Dänisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

528185

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

- 8 -

MODEL 1

Remove the 3 panels A as shown in Fig.4.

Pull handle B as shown in Fig.6.

MODEL 2

Open panel C as shown in Fig.5.

Pull handle B as shown in Fig.6.

If the appliance has a lid, remove it by removing the 4

screws B as shown in Fig.9A.

• WALL FIXING

Mark the position of the lower side of the hood on the

wall (Fig.2A). Maintain the minimum distance required

from the hob as shown in Fig.2B.

- Position the fixing template on the wall, making sure

that the line coincides with the line previously made on

the wall.

- Mark the fixing holes and cut them into the material

(Fig.3).

- Fix the 2 top screws K and screw anchors (Fig.3),

without tightening them completely.

- Place the appliance against the wall, align it in horizontal

position and tighten screws K (Fig.7).

- Once the adjustment has been completed, fix the hood

using the 2 screws C (Fig.8).

- When carrying out the fixing operations, use only screws

and screw anchors suited to the type of wall (e.g.

reinforced concrete, plasterboard etc.).

- If the screws and screw anchors are supplied with the

appliance, make sure that they are suited to the type of

wall to which the hood must be fixed.

• INSTALLATION OF MODELS WITHOUT DECORATIVE

DUCTS

EXTRACTOR HOOD

- Remove the 4 screws B as shown in (Fig.9A).

- Remove both grid E on the air outlet hole and lid M as

shown in (Fig.9B).

- Connect the hood to the flexible hose (not supplied)

and the hose to the air exhaust hole previously prepared

(Fig.9C).

- Fix the lid once again by using the 4 screws previously

removed in (Fig.9A).

• OPTIONAL ACCESSORIES

This model may have decorative ducts as optional

accessories - ask your retailer for information.

Before fixing the decorative ducts, remove both the 4

screws B and lid M, as shown in (Fig.10A-B).

A sound-absorbing kit is also available (to be ordered as

an OPTIONAL accessory) in order to increase the

quietness level of the hood. The sound-absorbing layer

must be applied to the back of the decorative panel. For

fixing operations, refer to the instructions supplied with

the kit.

• INSTALLATION OF MODELS WITH DECORATIVE

DUCTS

Make sure the electrical power supply is within the

measurements of the decorative connector.

Adjust the width of the support bracket of the top

connector (Fig.11C). Then fix it to the ceiling so that it is

on the same axis as the hood using screws A (Fig.11C)

adhering to the distance from the ceiling shown in

(Fig.11B). Connect flange C to the air exhaust hole using

flexible hose L (Fig.11D).

Slide the top duct into the bottom duct. Fix the bottom

duct to the hood using screws B (supplied) (Fig.11E).

Pull out the top duct as far as the bracket and fix it using

screws F (Fig.11C).

• FILTER HOOD

Please note:

The filters should be ordered as accessories from your

retailer.

We offer 2 different types of kit which can be used to

transform the EXTRACTOR hood into a FILTER hood,

in accordance with the type of appliance model

purchased. One kit contains extractable filters (fig. 10)

and the other contains circular filters (fig. 15).

1- If you find a bracket (such as the one indicated in fig.

14) included in the product packaging, this should be

fixed to the hood using the 6 screws supplied.

To replace the active carbon filters pull lever B outwards

as shown in (Fig.10).

2- If your product is not supplied with a bracket, this

means that the active carbon filter is a circular version

(fig. 15).

The filters should be fitted to the extraction assembly

inside the hood, by centring them and rotating them 90

degrees, until they click into place (Fig. 15).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to

cooking.

It is recommended to leave the appliance in operation

for 15 minutes after cooking is terminated in order to

completely eliminate cooking vapours and odours.

The proper function of the cooker hood is conditioned

by the regularity of the maintenance operations, in par-

ticular, the active carbon filter.

• The anti-grease filters capture the grease particles

suspended in the air, and are therefore subject to clog-

ging according to the frequency of the use of the appli-

ance.

In order to prevent fire hazard, it is recommendable to

clean the filter at a maximum of 2 months by carrying

out the following instructions:

- Remove the filters from the cooker hood and wash them

in a solution of water and neutral liquid detergent, leaving

to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several

washes. This is not cause for customer complaint nor

replacement of panels.

• The active carbon filters purify the air that is replaced

in the environment. The filters are not washable nor re-

useable and must be replaced at maximum every four

months. The saturation of the active carbon filter depends

on the frequency of use of the appliance, by the type of

cooking and the regularity of cleaning the anti-grease

filters.

• Clean the fan and other surfaces of the cooker hood

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO CWB 9910 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info