Bedienungsanleitung BEKO DFN16430G (Seite 34 von 48) (Englisch)

762685

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

34/EN

There might be residues of detergent

or rinse aid in the machine and/or on

the pieces being washed depending

on the step the programme you have

cancelled was in.

Salt indicator ( )

Please check the salt indicator on the

display to see whether there is adequate

amount of softening salt in the dishwasher

or not. You need to refill the salt reservoir

with salt whenever salt indicator appears

on the display of your machine.

Adjusting the water hardness level is

explained in Water Softening System

section.

Rinse Aid indicator ( )

Please check the rinse aid indicator on the

display to see whether there is adequate

amount of rinse aid in the dishwasher or

not. You need to refill the rinse aid reservoir

with rinse aid whenever rinse aid indicator

appears on the display of your machine.

Adjusting the amount of rinse

aid

1. After turning on the machine,

press and hold Time Delay and P keys

simultaneously for 3 seconds to enter the

settings menu.

2. Press P key until the drying indicator

starts flashing

3. Set to the appropriate level with the

Time Delay key.

4. Press the On/Off key to save.

No rinse aid dispensed in P:1 position

1 dose of rinse aid is dispensed in P:2

position.

2 doses of rinse aid are dispensed in P:3

position.

3 doses of rinse aid are dispensed in P:4

position.

End of programme

End of Programme indicator will light up

once the washing programme is over.

1. Press the On/Off key to turn off your

machine.

2. Close the tap.

3. Unplug the machine from the socket.

For energy saving, the machine is

automatically turned off following the

completion of the programme or if the

programme is not started.

Leave your dishes in the machine for

about 15 minutes to allow them cool

down after they are washed. Your

dishes will dry in a shorter time if you

leave the door of your machine ajar

during this period. This process will

increase the drying effectiveness of

your machine.

Water cut-off warning

If mains water is cut or water inlet tap is

turned off the machine cannot take water

in and P2 icon will flash on the programme

indicator. As long as the problem continues,

washing programme is paused and the

water inlet is checked regularly by the

machine; when the water is restored P2

icon will disappear after a while and the

washing programme resumes.

Overflowing warning

If the machine intakes too much water or

there is leakage at any of the components

then the machine will detect this and P1

icon will flash on the Programme indicator.

As long as the overflowing continues safety

algorithm will be active and try to discharge

the water. If overflowing stops and safety is

assured, P1 icon will disappear. If P1 does

not disappear, there is a permanent fault. In

this case the authorised service should be

contacted.

4 doses of rinse aid are dispensed in P:5

position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO DFN16430G Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BEKO DFN16430G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info