Bedienungsanleitung BEKO HBV60X (Seite 7 von 12) (Englisch)

556808

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

1A). The ange D, to which the air exhaust pipe is connected,

and a plug B, used to shut o the unused air outlet, are both

supplied with the product.

• This device may be installed in two dierent ways:

1. Fixing the hood to the lower part of the wall cabinet

(Fig.2)

- Make 4 holes in the wall cabinet respecting the measurements

indicated in gures 2 A-2 C.

- Position the hood underneath the wall cabinet and x it

into place using 4 screws (not supplied) suitable for the type

of cabinet.

2. Fixing the hood to the wall (Fig.2).

- Make 4 holes in the wall cabinet referring to the measurements

indicated in gures 2 A-2 B. - Hang the hood on the wall, using

the 2 holes H, align it in a horizontal position and x it denitively

to the wall using the two lower safety holes I (Fig. 2B). For the

various installations use screws and screw anchors suited to

the type of wall (e.g. reinforced concrete, plasterboard, etc.). If

the screws and screw anchors are provided with the product,

check that they are suitable for the type of wall on which the

hood is to be xed.

The hood is already prepared for the version with which it was

ordered. The versions may be:

- Extraction (Fig. 1A-3)

- Filter (Fig. 1B-4-7).

- If the hood is an extractor model, the lever C must be posi-

tioned as indicated in Fig. 3.

- If the hood is a lter model, the lever C must be positioned

as indicated in Fig. 4.

• Extractor version

The appliance expels the fumes through an outside wall or

a duct. It is necessary to buy a telescopic pipe in accordance

with the standards in use (inammable) and connect it to

ange D (Fig 1A). The ange D is supplied with the product

and should be xed above the air outlet hole of the hood as

indicated in Fig. 3.

• Filtering version

To transform an extractor hood version into a filter hood

version, please inquire with your retailer about purchasing

charcoal lters. The lters should be tted to the extraction

assembly inside the hood, by centring them and rotating them

90 degrees, until they click into place (Fig. 7). To do this, remove

the grille D (Fig. 5). Close the air outlet opening with the plug

B, as indicated in Fig. 4.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15

minutes after cooking is terminated in order to completely

eliminate cooking vapours and odours.

The proper function of the cooker hood is conditioned by the

regularity of the maintenance operations, in particular, the

active carbon filter.

• The anti-grease filters capture the grease particles suspended

in the air, and are therefore subject to clogging according to

the frequency of the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the

filter at a maximum of 2 months by carrying out the following

instructions:

- Remove the filters from the cooker hood and wash them

in a solution of water and neutral liquid detergent, leaving

to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes.

This is not cause for customer complaint nor replacement of

panels.

• The active carbon filters purify the air that is replaced in the

environment. The filters are not washable nor re-useable

and must be replaced at maximum every four months. The

saturation of the active carbon filter depends on the frequency

of use of the appliance, by the type of cooking and the regularity

of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly

using a cloth moistened with denatured alcohol or non abrasive

liquid detergent.

• The illumination installation is designed for use during cooking

and not for prolonged general illumination of the environment.

Prolonged use of the illumination installation notably reduces

the duration of the bulb.

• Replacing the acrylic or metal panels

To replace the acrylic or metal panels you need to rst remove

the grille D by pushing the two side buttons B inwards as

indicated in gure 5. Remove the two lter clips B (g. 6) and

the acrylic or metal panel C. To reassemble the part, simply

perform the procedure in reverse.

• FILTER REMOVAL

WARNING - ENSURE THE APPLIANCE IS SWITCHED OFF

AT THE MAINS BEFORE REPLACING THE BULBS AND

FILTERS.

1. remove the filters by lifting the recessed handle and lift

free from the hood frame.

2. To reinstall the filters position in the recess at the rear

and press to lock in position.

BULB REPALCEMENT

1. Remove the filters

2. Unscrew the bulb in an anti-clock wise direction.

3. After installing the correct replacement bulb, refit the

filter.

Replacement bulbs can be easily obtained from a good

electrical or DIY store.

BEFORE CALLING SERVICE/TROUBLE SHOOTING

The hood was switched on but the unit does not operate.

• Have you plugged in/switched on the power supply at

the socket?

• Check for a blown fuse/or trip.

Extraction is poor

• Check and clean the lters if required, if required, if active

lters are present replacement lters maybe required.

• Check that the exhaust ducting is not obstructed.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

- 7 -

BEKO HBV60X Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info