Bedienungsanleitung BEKO HCA61531X (Seite 30 von 88) (Alle Sprachen)

676962

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

- 28 -

sent back into the room and its function is to mitigate the

unpleasant odours produced by cooking.

- The non-regenerable active carbon filters must be replaced

at least every 4 months. The saturation of the active charcoal

depends on the more or less prolonged use of the appliance,

on the type of kitchen and on the frequency with which anti-

grease filter is cleaned.

- Regenerable active charcoal filters must be washed by hand,

with non abrasive neutral detergents, or in the dishwasher at

a maximum temperature of 65°C (the washing cycle must be

complete without dishware). Remove excess water without

damaging the filter, remove the plastic parts, and let the

mat dry in the oven for at least 15 minutes approximately at

a maximum temperature of 100°C. To keep the regenerable

charcoal filter functioning efficient this operation must be

repeated every 2 months. These must be replaced at least

every 3 years or when the mat is damaged.

•Beforeremountingtheanti-greasefiltersandtheregen-

erable active charcoal filters it is important that they are

completely dry.

•Cleanthehoodfrequently,bothinternallyandexternally,

using a cloth dampened with denatured alcohol or neutral

liquid detergents that are non abrasive.

• The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system significantly decreases

the average duration of the bulbs.

• If the appliance is equipped with courtesy lights it is possible

to use them for general room lighting for a prolonged amount

of time.

•Attention: the non compliance with the hood cleaning

warnings and with the replacement and cleaning of the filters

entails risk of fires. One therefore recommends keeping to the

suggested instructions.

•Replacinghalogenlightbulbs(Fig.15.1):

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

•ReplacingLEDlamps(Fig.15.2):

If the appliance version is with LED lamps, the intervention of

a specialised technician is necessary to replace them.

•Commandsluminous(Fig.16)the key symbols are ex-

plained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes (*)

If your appliance has the INTENSIVE speed function, from

speed THREE, press key E for 2 seconds and it will be activated

for 10 minutes after which it will return to the previously set

speed. When the function is active the LED flashes.

To interrupt it before the 10 minutes have elapsed, press

key E again.

Some models allow activating this function even with speed

one and two.

By pressing key F for two seconds (with the hood switched off)

the “clean air” function is activated. This function switches the

appliance on for ten minutes every hour at the first speed. As

soon as this function is activated the motor starts up at the

first speed for ten minutes. During this time key F and key

C must flash at the same time. After ten minutes the motor

switches off and the LED of key F remains switched on with

a fixed light until the motor starts up again at the first speed

after fifty minutes and keys F and C start to flash again for ten

minutes and so on. By pressing any key for the exclusion of

the hood light the hood will return immediately to its normal

functioning (e.g. if key D is pressed the “clean air” function is

deactivated and the motor moves to the 2nd speed straight

away. By pressing key B the function is deactivated).

(*)The “AUTOMATIC STOP TIMER” delays stopping of the

hood, which will continue functioning for 15 minutes at the

operating speed set at the time this function is activated.

•Anti-grease/activecharcoalfilterssaturation:

- When the A key flashes with a 2 second frequency the anti-

grease filters must be washed.

- When the A key flashes with a 0.5 second frequency the

active carbon filters must be replaced or washed depending

on the type of filter.

Once the clean filter has been put back one must reset the

electronic memory by pressing the A key for approximately 5

seconds until it stops flashing.

•Commands(Fig.17):

Push-button A = on/off lights switch.

Push-button B = on/off cooker hood switch. The appliance

switches on at speed level 1, If the cooker hood is on depress

the push-button for 2 sec. to switch off the cooker hood. If

the cooker hood is at speed level 1 it will not be necessary

to depress the push-button to switch the cooker hood off.

Decreases the motor speed.

Display C = indicates the motor speed level selected and

activates the timer.

Push-button D = switches on the cooker hood. Increases the

motor speed. Touching the key at 3rd speed, the intensive

function runs for 10’, then the appliance go back to work at

the original speed. During this function the display blinks.

Key E = The Timer times the functions on activation for 15

minutes, after which they are switched off. The Timer is deac-

tivated by re-pressing Key E.

When the Timer is activated the decimal point must flash on

the display. The Timer cannot be activated if the intensive

speed is functioning.

The “clean air” function is activated by pressing key E for 2

seconds when the appliance is switched off. This switches the

motor on for 10 minutes every hour at the first speed.

During functioning a rotary movement of the peripheral seg-

ments must be visualised on the display. When this time has

passed the motor switches off and the fixed letter “C” must

be visualised on the display until the motor re-starts after 50

minutes for another 10 minutes and so on.

Press any key apart from the light keys to return to normal

functioning. Press key E to deactivate the function.

•Anti-grease/activecharcoalfilterssaturation:

- When display item C flashes, at a speed where it alternates

with the letter F (e.g. 1 and F), the anti-grease filters must be

washed.

- When display item C flashes, at a speed where it alternates

with the letter A (e.g. 1 and A), the active carbon filters must

be replaced or washed depending on the type of filter.

After the clean filter has been positioned correctly, the

electronic memory must be reset by pressing button A for

approximately 5 seconds, until the indication F or A shown

on the display C stops flashing.

BEKO HCA61531X Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info