676962

BEKO HCA61531X Seite 31

31
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
- 29 -
•Commandsmechanical(Fig.18) the key symbols are ex-
plained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D = SPEED II
E = SPEED III.
•Mechanicalcontrols(Fig.19)the symbols are as follows:
A = LIGHT/ON-OFF key
B = OFF/FIRST SPEED key
C = SECOND SPEED key
D = THIRD SPEED key.
If the hood is shut off at first, second or third speed, when
it is turned back on, it will start at the same speed it was in
when switched off.
•Commands(Fig.20):
A = Light Key Turn on/off lights.
B = ON/OFF Key Turn on/off the hood.
The equipment switches on at the 1st speed.
To turn off the hood press key B.
C = Display Indicates the speed of the selected motor and
activation of the timer.
D = Key Increases and decreases the speed of the motor with
a cyclical pattern, 1°-2°- 3° ... 1°-2°- 3° speed.
By pressing the key for 3 seconds the INTENSE function comes
into operation for 6 minutes, on the C display the number 4
starts flashing.
At the end of the minutes the engine will start operating at
the previously set speed.
To deactivate the intense speed, before the set time, press
the B key and the hood turns off, but not if the lights are on.
E = Timer key With any speed entered (excluding Intense
speed) by pressing the key the timer function is activated for
15 min. At the end of the count the hood turns off (motor and
any lights that are on).
To turn off the Timer function, before the pre-set time, press
the B key and the hood turns off, or by pressing the timer key
again it turns off but the hood continues to operate.
•SaturationActivecarbon/Anti-greasefilters:
- After 30 h of operation, with the hood ON on display C , the
letter F starts to flash which means that the anti-grease filters
have to be washed.
Once the clean filter is replaced you must reset the electronic
memory, with the hood off press key B and D for 5 sec. until
the display C shows the letter F fixed for 2 sec.
-After 120 h of operation, with the hood ON on display C the
letter C starts to flash which means that the carbon filters
have to be washed or replaced.
Once the clean filter is replaced you must do a double re-set so
with the hood off press key B and D for 5 sec. until the display
C shows the letter F fixed for 2 sec.
Repeat and press key B and D for 5 sec. until display C shows
the letter C fixed for 2 sec. .
•Commands
(Fig.21)
A = ON/OFF key
Turns the hood on/off.
By pressing key A the LED flashes for 2 sec. then remains fixed
and the equipment starts in 1° speed.
To turn the hood off press key A again, the LED flashes for 2
sec. then it turns off.
B = FIRST SPEED KEY
C = SECOND SPEED Key/TIMER function
- Key C also activates the TIMER function.
- The key flashes for the full duration of the TIMER.
- With any speed entered (excluding Intense speed where
applicable) by pressing C for about 3 seconds the TIMER
function is activated for 15 min. At the end of the count the
hood turns off (motor and any lights that are on).
- To deactivate the Timer function, before the pre-set time,
press any key except the F key for ON/OFF Lights.
D = THIRD SPEED key/ INTENSE SPEED Function
- Key D also activates the INTENSE SPEED function.
- The key flashes for the full duration of the INTENSE SPEED
function.
- By pressing the key for 3 seconds the INTENSE function comes
on for 6 minutes.
- At the end of the minutes the engine will start operating at
the previously set speed.
To deactivate the intense speed, before the pre-set time, press
any key except the F key for ON/OFF Lights.
Attention! Some models only work up to the 3rd speed and,
therefore, do not have the intense function.
E = ON/OFF LIGHTS key
•SaturationActivecarbon/Anti-greasefilters:
- When the hood is on the LED corresponding to the A and B
keys flash, the anti-grease filters must be washed.
Once the clean filter is put back the electronic memory must
be reset, with the hood off press A for 5 sec. , the reset is
confirmed by a flashing of the LED A and B.
- When the hood is on the LED corresponding to C and E flash,
the carbon filters must be washed.
Once the clean filter is put back the electronic memory must
be reset, with the hood off press A for 5 sec. , the reset is
confirmed by a flashing of the LED C and E.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
… 31 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BEKO HCA61531X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info