Bedienungsanleitung BEKO HNE 51210S (Seite 12 von 60) (Alle Sprachen)

761456

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 50cm from electric cookers

and 70cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after

installation. If it not fitted with a plug (direct mains connection)

or if the plug is not located in an accessible area, after

installation, apply a double pole switch in accordance with

standards which assures the complete disconnection of the

mains under conditions relating to over-current category III, in

accordance with installation instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Warning! Power cable replacement must be undertaken by

the authorised service assistance centre or similar qualified

person.

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Before beginning installation:

• Remove the fats filter/s or the suction grill/s (depending

on the model in possession –see also the relative

paragraph). This/these is/are to be mounted once

installation is completed.

• Remove the active carbon (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

• Choose the discharge outlet to use:

Only filtering version: use ONLY the upper B1 outlet

(Fig. 2 - Fig. 2.2). Check that this, once installation is

completed, is not obstructed and that there is sufficient

space so that the purified fumes and steam can return

easily into the kitchen.

Press with decision (Fig. 3.1) to take away the pre-

fractured part (B1 o B2) that closes the discharge outlet

and remove it.

Install the connection ring on the open discharge outlet

(Fig. 3.2 bayonet embedded) or the deflector (*). (Fig.

3.3).

Check that the lateral wall units between which to install the

hood are sufficiently robust for installing the hood.

Otherwise mount the hooking brackets on the wall (*) to use

as additional supports:

a. Insert each bracket from the rear inside the hood

through the apposite slots (Fig. 4.1—Fig. 4.2).

b. Fix the brackets with the screws and threaded bushes

(Fig. 4.3).

Screw the headless screws halfway. They will serve to

adjust the position of the hood at the moment of

installation.

Note: the position of the brackets can be adjusted during

installation, suitably loosening and retightening the screws

that fix them to the hood. (Fig. 7 - S1-S2).

Installing the aesthetic panel (*)

a. Extract the steam collector (freeing it from the blocking

hooks - Fig. 5).

b. Put perforation diagram N3 on the REAR of aesthetic

panel J (the arrow on the diagram turned upward towards

the UPPER EDGE of the aesthetic panel). Fig. 6

c. Make BLIND HOLES K as indicated. Fig. 6

d. Put the steam collector over the aesthetic panel and fix it

with 8 screws L. Fig. 6

e. Remount the door on the hood, first on upper guides M1,

then on the lower M2. Fig. 6

f. Close completely and re-open the door to check its

correct sliding on the guides.

Electrical or mechanical valve (*)

Fig. 11

In some products an electrically or mechanically activated

valve is envisaged instead of an aspiration motor.

This is usually installed on discharge outlet B1 and fixed to the

caisson of the hood with 3 screws, while a stopper is installed

in outlet B2, fixed in its turn with 1 screw.

If you want to install the valve on outlet B2, dismantle the

valve from the caisson, remove the fixing screws, and install it

in place of the stopper, the latter to be fixed on the cover of

outlet B1.

Installation

a. Use perforation diagram N2 (*). Position the diagram on

the front edges of the wall unit (right wall unit, B side) –

(left wall unit, C side) WITHOUT CONSIDERING THE

THICKNESS OF THE DOORS, and make the holes as

indicated. Fig. 8

b. If necessary, fix the hood to the wall, putting template N1

(*) on the wall so its upper edge coincides with the upper

edge of template N2 (*). Fig. 7-8

c. Make the holes as indicated. Fix 2 hooks (*) R to the wall

with screws and dowels. Fig. 7

BEKO HNE 51210S Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info